MTX Audio Speaker 620CE User Manual

21A3089  
FIRST  
CLASS  
STAMP  
HERE  
MODEL 620CE  
IN CEILING ENCLOSED LOUDSPEAKER  
OWNERS MANUAL  
4545 E BASELINE RD  
PHOENIX AZ 85040-6400  
 
OTHER BLUEPRINT SERIES PRODUCTS FROM MTX  
MTX offers a wide assortment of audio components. Ranging from in-wall  
speakers to amplifiers to accessories. Each component is value engi-  
neered and must meet strict quality control standards before it becomes  
part of the MTX product line.  
FEATURES  
The Model 620CE in-ceiling enclosed loudspeaker is a  
unique design unlike any other before it. It allows you to bring  
concert-quality sound to virtually any area of your home that  
may have been previously off-limits because of building code  
restrictions or weather conditions.  
Listed below you will find a sampling of MTX components available from  
your authorized Blueprint Series dealer.  
IN-WALL LOUDSPEAKERS  
MODEL 520W  
MODEL 502W  
5-1/4” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/84dB Sensitivity  
53Hz-20kHz Frequency Response  
50 Watts RMS/160 Watts Total  
11”H x 7-1/2”W x 2-1/2”D  
5-1/4” Two-Way In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/84dB Sensitivity  
53Hz-20kHz Frequency Response  
45 Watts RMS/140 Watts Total  
11”H x 7-1/2”W x 2-1/2”D  
The Model 620CE utilizes its mounting wings to mount into  
a ceiling like conventional in-ceiling speakers, while incorporating  
an integral enclosure to provide a vapor barrier between you  
and the outside world.  
MODEL 620W  
6-1/2” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/85dB Sensitivity  
43Hz-20kHz Frequency Response  
55 Watts RMS/180 Watts Total  
12-1/16”H x 8-9/16”W x 2-7/8”D  
MODEL 602W  
6-1/2” Two-Way In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/85dB Sensitivity  
43Hz-20kHz Frequency Response  
50 Watts RMS/160 Watts Total  
12-1/16”H x 8-9/16”W x 2-7/8”D  
The long excursion, high performance woofer was  
designed specifically to work with its integral enclosure to insure  
deep, accurate bass. While the soft dome tweeter perfectly com-  
plements the woofer with its sweet sound and excellent off-axis  
frequency response.  
MODEL 820W  
8” Two-Way In-Wall Speaker  
1” Soft Dome Tweeter  
8 Ohm Impedance/86dB Sensitivity  
33Hz-20kHz Frequency Response  
60 Watts RMS/200 Watts Total  
14-1/16”H x 10-1/16”W x 3-1/2”D  
MODEL 600WM  
6-1/2” Water Resistant Co-Axial In-Wall Speaker  
1/2” Polycarbonate Dome Tweeter  
8 Ohm Impedance/88dB Sensitivity  
64Hz-20kHz Frequency Response  
35 Watts RMS/140 Watts Total  
8-5/8”H x 8-5/8”W x 2-3/4”D  
All of the Model 620CE components have been manufac-  
tured with high quality, weather resistant materials. This completes  
the Model 620CE’s package of versatility, performance and dura-  
bility.  
SPEAKER/AMPLIFIER SELECTOR  
LPS-600  
Accommodates up to 6 pair of speakers  
Handles up to 250 Watts/channel continuous (RMS)  
Impedance Protection Circuitry  
Low profile-full size component  
Two-piece, plug in connectors on the rear panel  
Accommodates up to 14 gauge wire  
TV-5 UL Approved Switches  
A/B Amplifier and Input Selector  
ACCESSORIES  
VC-30B/VC-30W  
Decora-Style Volume Control (Bone or White)  
10 Step 25 Watts per channel (RMS) 150 Watts Peak  
AB-1SB/AB-1SW  
Decora-Style A/B Switch (Bone or White)  
PCK65C  
Pre-Construction Kit for Model 610RCM  
PCK85C  
Pre-Construction Kit for Model 810RCM  
 
STEP 1  
STEP 4  
Using a stud finder (available at low cost at most hardware stores) or  
other accurate method, locate center point between two joists and  
mark. Using template provided, trace hole pattern on surface of ceiling.  
Attach loudspeaker wires to speaker terminals, observing correct polarity,  
and position speaker frame up into cutout. Be careful not to pinch wires in  
the process.  
STEP 5  
STEP 2  
Carefully tighten the four mounting screws, using a phillips screwdriver. This  
will cause the mounting wings to rotate out behind the mounting surface  
and secure the speaker in place. Note: the phillips head screws are for tight-  
ening the mounting wings. The torx head screws are for the enclosure which  
should not be tightened or loosened.  
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in ceil-  
ing, following traced pattern.  
STEP 3  
Run loudspeaker wires to sound source location. There are several meth-  
ods you can use to accomplish wiring, depending on the construction  
characteristics of the room or house. You can add a professional touch  
to your installation by using a speaker terminal plate at the source loca-  
tion. Leave sufficient amount of wire at speaker location (8 to 10 inches)  
to complete connection.  
STEP 6  
After speaker panel is secured tightly, test for sound. When you are satisfied  
the speaker is operational, affix grill. As the grill is designed for a snug fit, you’ll  
need to position one edge into the slot first, press or squeeze around perime-  
ter of the grill, while pushing leading edge into the grill slot.  
 

Miele Dishwasher G 841 PLUS User Manual
Miller Electric Welder XL AC DC User Manual
MTD Lawn Mower MMZ 2254 User Manual
Murphy Portable Generator MGC447 User Manual
NETGEAR Switch GSM7224R User Manual
Nikon Marine GPS System ver100 User Manual
Nostalgia Electrics Refrigerator KRS 2000 Series User Manual
Omega Speaker Systems Network Router HX93A User Manual
Omega Vehicle Security Thermometer HH501BK User Manual
Oregon Scientific Stud Sensor UVR128 User Manual