Oreck Vacuum Cleaner 2005HH User Manual

®
S I M P L Y  
A M A Z I N G  
USERS GUIDE  
2005HH  
2005RH  
COMMERCIAL  
HIGH SPEED UPRIGHT VACUUM  
CLEANER WITH  
®
CLEANING SYSTEM  
SAVE THIS BOOKLET!  
Includes:  
• Safety Warnings  
• Warranty  
• Operating Instructions  
• Trouble Diagnosis  
• Accessories  
 
Accessories  
Maintenance and  
Customer Service  
(Sold Separately)  
ITEM  
PART NUMBER  
Your ORECK vacuum cleaner is a product of  
precise engineering. The motor bearings are  
permanently lubricated and should not be oiled.  
If you require additional information or have  
problems with your ORECK appliance, or to order  
new bags or spare parts, you may call ORECK  
customer service at: (0) 01279 406995.  
1. Dust Bag, 9 Pack  
Hypo-Allergenic  
PK80009DW  
PK80009  
0300604  
AIRTABS  
Regular  
2. Belts, 3 Pack  
®
3. Oreck Fresh Air Tabs  
Or write to:  
Oreck Commercial  
21 Greenway Business Centre  
Harlow Business Park, Greenway  
HARLOW  
Essex  
U.K.  
CM19 5QE  
Please specify the model number and serial/code  
number which can be found on the data plate on the  
back of the vacuum.  
Save your sales or purchase slip. Should your  
ORECK appliance require warranty service, present  
this slip to the Authorized Service Center as your  
proof of purchase date.  
Warranty  
ORECK MANUFACTURING COMPANY: (Oreck 21180 Johnson Road;  
Long Beach, MS, USA 39560 gives you the following warranty for this  
product only if it was originally purchased for residential use, not resale  
from Oreck or an Oreck Authorized Retail Dealer.)  
Oreck will repair or replace, free of charge, to the original purchaser, any  
part that is found to be defective in material or workmanship within one  
(1) year of date of purchase. This limited warranty covers the revolving  
roller brush for thirty (30) days from the date of purchase.  
This warranty does not cover the replacement of expendable or  
consumable parts such as carbon motor brushes, edge brushes, belts,  
bulbs, disposable bags and other parts subject to normal wear unless  
they are defective in material or workmanship.  
This warranty does not apply to any part subjected to accident, abuse,  
alteration, misuse, damage caused by act of God, the use of voltages  
other than indicated on the serial number displayed on this product or  
service of this product by other than Oreck or a participating Factory  
Authorized Service Center.  
Oreck does not authorize any person or representative to assume or  
grant any other warranty obligation with the sale of this product.  
Oreck’s warranty is valid only if you retain proof of purchase from Oreck  
or an Oreck Authorized Retail Dealer for this product. If you purchase this  
product from any other source, your purchase is “AS IS,” which means  
Oreck grants you no warranty, and that you, not Oreck, assume the entire  
risk of the quality and performance of this product, including the entire  
cost of any necessary servicing or repairs of any defects.  
This warranty is in addition to your statutory and other legal rights.  
**Reconditioned units carry a 6 month warranty from date of purchase.  
3
 
To Replace Filter  
Dust Bag  
Assembly  
To assist you in assembling your  
cleaner, the parts have been  
10  
WARNING: Unplug cord from  
electrical outlet before servicing.  
11  
numbered as follows  
:
9
1 Handle section, upper  
2 Tube, lower  
3 Power head  
1
12  
BAG INSTALLATION:  
17  
16  
1. Hook bottom of bag collar  
opening under lip “B” of  
connector assembly. Pull up  
on bag collar and snap over  
lip “A” of connector.  
4 Outer bag  
A
5 Paper filter dust bag  
6 Power cord  
5
13  
2
4
8
B
7 Retaining spring  
8 Bag tension bar  
9 Zip fastener  
10 On/off switch  
11 Cord hook  
6
2. Press on edges of bag collar  
to insure bag is completely  
installed.  
12 Plastic loop/cable clamp  
13 Connector assembly  
14 Fan housing  
14  
7
15  
15 Cord assembly  
3
16 Handle Brace  
17 Cord Strain Relief  
Before assembling appliance,  
1
remove two screws from connector  
assembly. Remove cardboard  
insert by pulling upward.  
IMPORTANT: Check to  
make sure bag collar is  
behind lips “A” and “B”. If it  
is not, dust will leak into  
outer bag. When filter bag is  
in place, close outer bag  
with zipper fastener.  
Connector  
Assembly  
With On/Off switch facing the  
front of the unit, slide upper  
Upper  
2
Handle  
handle section over matching  
section of the connector assembly.  
Place brace against handle and  
connector assembly aligning  
screw holes. Insert short screw into  
top hole and long screw into  
bottom hole then tighten firmly  
until handle is no longer loose.  
Using An Oreck  
®
Fresh Air Tab  
Brace  
Your ORECK XL vacuum  
cleaner has a special  
FRESH AIR tab pocket. This  
pocket is located inside the  
outer bag in the area  
where the disposable  
paper bag attaches to the  
intake tube. Insert tablet in  
pocket.  
Connector  
Assembly  
Attach cord to cord clip by  
pressing cord above and below  
clip ensuring the cord is fully rested  
in clip.  
3
4
 
Operating Instructions  
To Operate  
All paper dust bags are not the same. Your ORECK  
disposable dust bags have been designed to be  
used with the ORECK cleaner. Using bags other  
than genuine ORECK disposable bags will affect  
the cleaning ability of your cleaner and could  
cause damage to it.  
Make sure the disposable paper filter dust bag is in place.  
DO NOT operate the cleaner without a paper filter dust bag.  
Plug the power cord into an electrical outlet.  
Press the ON(l) - OFF(O) switch on handle assembly when  
ready to operate.  
General Information  
The Belt  
The performance of your new cleaner greatly depends upon  
care and maintenance. The instructions in this manual will  
guide you in performing basic care and maintenance. To  
obtain the most satisfying years of service, read the  
instructions and keep them handy for future reference.  
The belt on your vacuum cleaner controls the speed of the  
revolving brush and is very important for the effective  
operation of the cleaner. If the belt becomes stretched or cut,  
it will cause the revolving brush to stop completely or slow  
down. See instructions in the manual for replacing belt.  
An extra belt is stored in the baseplate of your  
cleaner. When buying replacement belts, use ONLY  
ORECK genuine belts. Belts other than ORECK belts  
will not operate the revolving brush correctly and  
may create undue stress which will cause damage  
to the motor and brush bearings. Using belts other  
than ORECK belts will void the warranty.  
Operating Recommendations  
This new ORECK XL High-Speed Upright is one of the finest,  
fastest, and strongest units in its class. You’ll love the way it  
cleans, gets under things, and it’s SO lightweight and easy to  
use.  
The following are a few simple suggestions regarding its  
operation:  
1. When inserting a new disposable paper filter dust bag—  
FIRST PUFF OUT and OPEN THE BAG.  
Lubrication  
The vacuum cleaner motor bearings are factory lubricated  
and sealed. Further lubrication is not required.  
2. When the disposable filter dust bag is full, REPLACE IT.  
3. If at any time the machine does not pick up properly or  
makes an unusual noise, STOP OPERATION and service.  
4. Although your upright will pick up pins, paper clips, and  
other small objects, it is recommended that these be  
removed from the floor before you vacuum. Failure to do  
so may result in permanent damage to the motor suction  
fan and its housing.  
General Cleaner Care  
At least once a month, check revolving brush for excessive  
lint, string or hair. Remove this material.  
Wipe the inside and outside  
of the outer vinyl bag and the  
outside of the cleaner with a  
damp cloth. Also clean the  
connector deflector assembly  
area, base of cleaner and fan  
housing area. If there is dust  
in the outer bag, vacuum it or  
shake it out.  
A little preventative maintenance  
will keep your cleaner looking  
new and will ensure continued  
cleaning effectiveness.  
5. WARNING: Do not use your vacuum cleaner on damp  
or wet surfaces. This will cause damage to the vacuum  
cleaner and is dangerous to the user. Damage caused by  
use on wet or damp surfaces is not covered under  
warranty.  
6. REPLACE THE BELT EVERY 6 MONTHS.  
7. Change the disposable filter dust bag at least once a  
month—even if it is not full! The collected dust in the dust  
bag can cause odor, attract moisture, act as a breeding  
area and can affect the efficiency of the cleaner.  
8. Do not run the vacuum cleaner over cord. The  
revolving brush could damage the cord.  
9. Use caution when vacuuming over area rug edges and  
fringe.  
Cord Strain Relief  
The cord strain relief located on the upper section of the handle  
is designed to reduce stress on the cord at the base of the  
handle.  
Disposable Paper Filter Dust Bags  
Disposable paper filter dust bags play a very important role  
in the efficiency of your ORECK vacuum cleaner. The purpose  
of the paper bag is to trap dirt, but at the same time it must  
be porous enough to allow air to pass through. If the paper  
bag becomes clogged, no air can pass through the cleaner  
and cleaning cannot take place, regardless of the cleaner’s  
power.  
Should the power cord come  
loose from the cord strain  
relief, it can be easily  
reattached.  
To attach the power cord to  
the cord strain relief, grasp the  
Cord Strain  
power cord approximately 12  
Relief  
To keep your cleaner operating at maximum efficiency,  
change the dust bag frequently. DO NOT FILL ABOVE THE  
LINE INDICATED ON THE DUST BAG.  
Be sure the disposable paper filter dust bag is in proper  
position, over the lower lip and the top lip of the connector.  
inches from the base of the  
Clamp  
handle. Pinch power cord  
together and slide approxi-  
mately 1-2 inches through the  
bottom hole in flat side of cord  
strain relief. Carefully slide  
power cord loop over clamp  
on cord strain relief and pull  
excess until the power cord is tightly rested under clamp.  
5
 
How to Replace a Worn Belt  
Operating Instructions  
WARNING: Unplug cord from  
electrical outlet before servicing.  
CAUTION—WOOD FLOORS, SOFT (VINYL, ASPHALT TILE,  
ETC.) FLOOR SURFACES AND POLISHED FLOOR FINISHES  
Use floor and floor finish manufacturer’s recommended  
methods of cleaning. The metal strip on the base of the  
cleaner could be damaged if used on concrete or abrasive  
surfaces, and, therefore, cause damage to wood floors, soft  
(vinyl, asphalt tile, etc.) floor surfaces and polished floor  
finishes. The roller brush may also scuff very soft finishes. Do  
not operate the unit while in the upright and locked position.  
Do not let the unit run while in any one stationary position for  
any period of time. Keep the unit moving while in operation.  
Remove the replacement  
belt from the storage  
channel.  
Celoc® Hypo-Allergenic Filter System: 2005HH  
The CELOC SMMS outer bag of your vacuum cleaner is high  
filtration medical material designed to filter the smallest of  
dust particles. It is important the inside of the outer bag be  
cleaned. Vacuum the inside of the outer bag or hand wash,  
turned inside out, with warm water, and air dry. For best  
results, the CELOC SMMS outer bag should be replaced  
once a year. The CELOC layered disposable inner dust bag  
must be replaced once a month even if it is not full.  
Change it more often if it is used in extremely dirty areas.  
Increase the cleaning power of your vacuum by changing the  
bag often.  
Remove the door by  
removing the hold down  
screw located on side of  
power head.  
Slide the door forward  
by prying open with a  
screwdriver or coin.  
Remove the belt from the  
brush roll pulley and the  
motor drive shaft.  
Loop the new belt over  
the motor drive shaft.  
Place the opposite end of  
the belt on the brush roll  
pulley. Rotate the brush  
roll three (3) complete  
revolutions to ensure that  
no part of the belt is  
overhanging the end of  
the motor drive shaft.  
Replace the door by  
sliding it into the groove  
at the bottom of the  
housing. Replace the  
hold down screw.  
6
 
To Adjust or Replace Brush  
Stuffing or Blockage  
Under certain conditions it is possible to stuff or block the intake  
tube and the lower tube assembly. If your vacuum cleaner does  
not pick up properly, or makes unusual noise and the outer bag  
does not fluff up or balloon open, follow the following steps:  
WARNING: Unplug cord from  
electrical outlet before servicing.  
To determine if the brush is  
worn, place a firm straight  
edge across the nozzle  
opening. If brush bristles  
do not extend beyond  
baseplate, brush should be  
adjusted.  
WARNING: Unplug cord from electrical  
outlet before servicing.  
1. Check for blockage at the  
mouth of the intake  
opening. See illustration A.  
If there is blockage, remove  
it with long-nose pliers, a  
screwdriver or coat hanger.  
If you can not reach the  
blockage, remove  
Remove the baseplate by  
removing 5 screws. Then,  
remove the belt and brush  
roll from the housing.  
A
Intake Opening  
baseplate. See illustration B.  
2. If the blockage is not at the  
base, remove lower tube.  
See illustration C. Unhook  
retainer spring, releasing  
bottom of bag. Twist lower  
collar counterclockwise to  
slide up. Pull tube out of  
base. Check for blockage.  
If blockage is in the tube,  
remove with a coat hanger.  
3. If tube is not blocked, look  
into fan housing. See illus-  
tration D. Remove debris  
with long-nose pliers, a  
Rotate both bearing assem-  
blies at ends of brush roll  
to show “OLD” and  
replace in the holding  
channels in the housing.  
Retainer  
Spring  
NOTE: The bearing  
assembly setting marked  
“OLD” has a smooth side.  
The one marked “NEW”  
C
has a notch. When  
rotating bearings, make  
sure both bearing  
Rotate and match  
bearing assemblies  
screwdriver or coat hanger.  
4. To reassemble, check O-ring  
on tube, and replace if  
Fan  
Housing  
assembly settings are the  
same and face up when  
replacing the brush roll.  
damaged. Vacuum will not  
operate properly without the  
tube O-ring. Slide O-ring to  
approximately 2" from base  
of tube. Replace tube by  
first lining up slot at base of  
tube with inner tab inside  
fan housing. Then reinsert  
tube and push down until  
the tube is seated. Make  
sure O-ring is in place  
O-ring  
Reassemble the belt and  
the baseplate and check  
bristle height above  
baseplate at each end of  
brush.  
D
E
against fan housing  
opening. Replace and  
If a previous adjustment  
has already been made  
and bristle height does not  
extend above baseplate, a  
new brush assembly  
tighten collar until collar  
locking tabs are locked in  
place. See illustration E.  
Make sure collar is not cross  
threaded on housing.  
IMPORTANT: Unless  
the brush is worn as  
indicated above,  
both bearings must  
be in the “NEW”  
position. When  
should be ordered.  
rotating, both  
bearings must be in  
the ”OLD” position.  
Unmatched settings  
will cause damage  
to your machine.  
7
 
Stuffing or Blockage  
Troubleshooting Guide  
5. Many times blockage occurs  
due to a full dust bag  
WARNING: Unplug cord from  
electrical outlet before servicing.  
F
causing dirt to back down  
Connector  
Deflector  
Opening  
SAVE SERVICE CALLS...CHECK THESE FIRST:  
• Is the disposable filter dust bag full?  
the air flow system. When  
that happens, the blockage  
will be at the top of the  
system, starting in the area  
where the dust bag connects  
to the connector assembly.  
See illustration F.  
• Are pores of filter dust bag clogged with powder or fine dust?  
• Is anything clogging the revolving brush, lower tube, intake  
opening, fan housing or connector assembly opening?  
• Is the belt in place and turning the brush?  
• Are the brush ends in the proper location?  
• Does the brush turn freely? Are hair, string or rug fibers wound  
around the brush?  
PROBLEM  
POSSIBLE SOURCE  
AREAS TO CHECK  
CLEANER  
Not plugged in  
properly.  
Be sure cleaner is  
firmly plugged  
WILL NOT RUN  
into wall outlet.  
NOTE: If the Stuffing or Blockage instructions do not correct the  
problem, contact an ORECK Authorized Service Center or call  
the Commercial Customer Service Center at (0) 01279 406995.  
No electricity in  
wall outlet.  
Check electrical  
source–fuse or  
circuit breaker.  
CLEANER  
Filter bag is full.  
Replace filter bag.  
See “To Replace  
Paper Filter Dust  
Bag.”  
DOES NOT PICK UP  
IMPORTANT: On plush and new carpets, stuffing may occur  
due to excessive fuzz and loose cuttings in the carpet.  
Stuffing could occur for the first few cleanings until all the  
loose material is removed. Due to the high efficiency of the  
cleaner, many older carpets will cause stuffing when the  
cleaner is first used on them.  
Nozzle or intake  
pivot clogged.  
Clear obstruction.  
Belt is broken or  
stretched.  
Replace belt.  
Brush is worn.  
See “To Adjust or  
Replace Brush.”  
Bag tube clogged. Clear obstruction.  
Bag pores are  
clogged with fine  
dust.  
Change bag.  
Impeller fan is  
broken.  
Return to Service  
Center for repair.  
Revolving brush is Check brush roll  
not even at both  
ends.  
end cards. Make  
sure words “OLD”  
or “NEW” match  
at each end.  
ALL OTHER SERVICING SHOULD BE DONE BY AN  
ORECK AUTHORIZED SERVICE CENTER.  
COMMERCIAL CUSTOMER SERVICE  
(0) 01279 406995  
Whenever calling, please be sure to have your model and  
serial number from data plate.  
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings,  
LLC. Printed in America.  
75319-10 REV A  
11/05 ECN# R-8058 & 8199  
 

Miele Oven 09 800 830 User Manual
Multiquip Saw SP118 User Manual
Newcon Optik Binoculars NV66 G2 5x User Manual
NordicTrack Home Gym NTE11920 User Manual
Omron Nebulizer NE U03V User Manual
Oster Blender 146360 REVA User Manual
Oster Mixer 2534 User Manual
Ozaki Worldwide Portable Speaker EM679 User Manual
Palm Mouse 3245WW User Manual
Panasonic Vacuum Cleaner MC CG901 User Manual