Oreck Vacuum Cleaner 2635RH User Manual

®
S I M P L Y  
A M A Z I N G  
USERS GUIDE  
2635RH  
HIGH SPEED UPRIGHT VACUUM  
CLEANER WITH  
®
CLEANING SYSTEM  
SAVE THIS BOOKLET!  
Includes:  
• Safety Warnings  
• Warranty  
• Operating Instructions  
• Trouble Diagnosis  
• Accessories  
 
Maintenance and  
Customer Service  
Your ORECK vacuum cleaner is a product of precise  
engineering. The motor bearings are permanently  
lubricated and should not be oiled. If you require  
additional information or have problems with your  
ORECK appliance, or to order new bags or spare  
parts, you may call ORECK customer service at:  
ACCESSORIES  
ITEM  
PART NUMBER  
®
1. Dust Bag, 8 Pack, Saniseal  
Hypo-Allergenic  
CCPK8DW  
CCPK8  
Dust Bag, 8 Pack, Regular  
2. Belts, 3 Pack  
0300604  
AIRTABS  
0845 603 0153  
®
3. Oreck Fresh Air Tabs  
Or write to:  
4. Light Bulb  
00965-0019  
Oreck UK  
P.O. Box 201  
Exeter  
DEVON  
EX1 1XB  
Attention: Oreck Customer Service  
Please specify the model number and serial/code  
number which can be found on the data plate on the  
back of the vacuum.  
Save your sales or purchase slip. Should your  
ORECK appliance require warranty service, present  
this slip to the Authorized Service Center as your  
proof of purchase date.  
Warranty  
ORECK MANUFACTURING COMPANY: (Oreck 21180 Johnson Road;  
Long Beach, MS, USA 39560 gives you the following warranty for this  
product only if it was originally purchased for residential use, not resale  
from Oreck or an Oreck Authorized Retail Dealer.)  
Oreck will repair or replace, free of charge, to the original purchaser, any  
part that is found to be defective in material or workmanship within  
three (3) years of date of purchase; ten (10) years on housing. This  
warranty applies to normal domestic use. Any commercial use of this  
product will void this warranty. This limited warranty covers the revolving  
roller brush for one (1) year for residential use only.  
This warranty does not cover the replacement of expendable or  
consumable parts such as carbon motor brushes, edge brushes, belts,  
bulbs, disposable bags and other parts subject to normal wear unless  
they are defective in material or workmanship.  
This warranty does not apply to any part subjected to accident, abuse,  
alteration, misuse, damage caused by act of God, the use of voltages  
other than indicated on the serial number displayed on this product or  
service of this product by other than Oreck or a participating Factory  
Authorized Service Center.  
Oreck does not authorize any person or representative to assume or  
grant any other warranty obligation with the sale of this product.  
Oreck’s warranty is valid only if you retain proof of purchase from Oreck  
or an Oreck Authorized Retail Dealer for this product. If you purchase this  
product from any other source, your purchase is “AS IS,” which means  
Oreck grants you no warranty, and that you, not Oreck, assume the entire  
risk of the quality and performance of this product, including the entire  
cost of any necessary servicing or repairs of any defects.  
This warranty is in addition to your statutory and other legal rights.  
*Reconditioned units carry a 1 year warranty from date of purchase.  
3
 
To Replace Filter  
Dust Bag  
Assembly  
To assist you in identifying  
WARNING: Unplug cord from  
electrical outlet before servicing.  
components of your vacuum,  
the parts have been numbered  
10  
11  
BAG REMOVAL:  
1. Unsnap bag door from base.  
2. Gently pull bag from  
cardboard collar upwards.  
9
as follows  
:
1
1 Handle tube, upper  
2 Tube, lower  
12  
3 Power head  
4 Outer bag  
5
5 Paper filter dust bag  
6 Power cord  
13  
4
8
7 Retaining spring  
8 Bag tension bar  
9 Zip fastener  
6
2
10 On/off switch  
11 Cord hook  
15  
12 Plastic loop/cable clamp  
13 Connector assembly  
14 Fan housing  
14  
7
15 Cord assembly  
3
3. Dust seal will close  
automatically  
Before assembling appliance,  
remove two screws from  
connector assembly. Remove  
cardboard insert by pulling  
upward.  
1
BAG INSTALLATION:  
1. Slide the cardboard collar  
completely onto bag dock  
door.  
With ON/OFF switch facing  
the front of the unit, slide  
upper handle section over  
matching section of the  
2
connector assembly. Insert  
short screw into top hole and  
long screw into bottom hole  
then tighten firmly until handle  
is no longer loose.  
Attach cord assembly to cord  
clip by pressing cord above  
and below clip ensuring the  
cord is fully rested in clip.  
3
JUSQU’À  
ENTENDREUN BRUIT  
PRESIONE
ESCUCHAR UN  
CHASQUIDODE SUJECIÓN  
2. Firmly push bag dock door  
with both thumbs on  
indication point until  
it snaps.  
4
 
Operating Instructions  
To Operate  
All paper dust bags are not the same. Your ORECK  
disposable dust bags have been designed to be used with the  
ORECK cleaner. Using bags other than genuine ORECK  
TYPE CC disposable bags will affect the cleaning ability of  
your cleaner and could cause damage to it.  
Make sure the disposable paper filter dust bag is in place.  
DO NOT operate the cleaner without a paper filter dust bag.  
Plug the power cord into an electrical outlet. Press the ON(l) -  
OFF(O) switch on handle assembly when ready to operate.  
General Information  
The Belt  
The performance of your new cleaner greatly depends upon  
care and maintenance. The instructions in this manual will  
guide you in performing basic care and maintenance. To  
obtain the most satisfying years of service read the instructions  
and keep them handy for future reference.  
The belt on your vacuum cleaner controls the speed of the  
revolving brush and is very important for the effective  
operation of the cleaner. If the belt becomes stretched or cut,  
it will cause the revolving brush to stop completely or slow  
down. See instructions in the manual for replacing belt.  
An extra belt is stored in the baseplate of your cleaner. When  
buying replacement belts, use ONLY ORECK genuine belts.  
Belts other than ORECK belts will not operate the revolving  
brush correctly and may create undue stress which will cause  
damage to the motor and brush bearings. Using belts other  
than ORECK belts will void the warranty.  
Operating Recommendations  
This new ORECK XL High-Speed Upright is one of the finest,  
fastest, and strongest units in its class. You’ll love the way it  
cleans, gets under things, and it’s SO lightweight and easy to  
use.  
The following are a few simple suggestions regarding its  
operation:  
Lubrication  
The vacuum cleaner motor bearings are factory lubricated  
and sealed. Further lubrication is not required.  
1. When inserting a new disposable paper filter dust bag—  
FIRST PUFF OUT and OPEN THE BAG.  
2. When the disposable filter dust bag is full, REPLACE IT.  
3. If at any time the machine does not pick up properly or  
makes an unusual noise, STOP OPERATION and service.  
4. Although your upright will pick up pins, paper clips, and  
other small objects, it is recommended that these be  
removed from the floor before you vacuum. Failure to do  
so may result in permanent damage to the motor suction  
fan and its housing.  
General Cleaner Care  
At least once a month, check  
for and remove excessive lint,  
string or hair from revolving  
brush.  
Wipe the outside of the  
cleaner with a damp cloth.  
Also clean the connector  
deflector assembly area, base  
of cleaner and fan housing  
area. If there is dust in the  
outer bag, vacuum it or shake  
it out.  
5. WARNING: Do not use your vacuum cleaner on damp  
or wet surfaces. This will cause damage to the vacuum  
cleaner and is dangerous to the user. Damage caused by  
use on wet or damp surfaces is not covered under  
warranty.  
6. REPLACE THE BELT EVERY 6 MONTHS.  
7. Change the disposable filter dust bag at least once a  
month—even if it is not full! The collected dust in the dust  
bag can cause odor, attract moisture, act as a breeding  
area and can affect the efficiency of the cleaner.  
8. DO NOT run the vacuum cleaner over cord. The  
revolving brush could damage the cord.  
A little preventative maintenance will keep your cleaner  
looking new and will ensure continued cleaning effectiveness.  
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile,  
etc.) Floor Surfaces and Polished Floor Finishes  
Use floor and floor finish manufacturer’s recommended  
methods of cleaning. The metal strip on the base of the  
cleaner could be damaged if used on concrete or abrasive  
surfaces, and, therefore, cause damage to wood floors, soft  
(vinyl, asphalt tile, etc.) floor surfaces and polished floor  
finishes. The roller brush may also scuff very soft finishes. Do  
not operate the unit while in the upright and locked position.  
Do not let the unit run while in any one stationary position for  
any period of time. Keep the unit moving while in operation.  
9. Use caution when vacuuming over area rug edges and  
fringe.  
Disposable Paper Filter Dust Bags  
Disposable paper filter dust bags play a very important role  
in the efficiency of your ORECK vacuum cleaner. The purpose  
of the paper bag is to trap dirt, but at the same time it must  
be porous enough to allow air to pass through. If the paper  
bag becomes clogged, no air can pass through the cleaner  
and cleaning cannot take place, regardless of the cleaner’s  
power.  
To keep your cleaner operating at maximum efficiency,  
change the dust bag frequently. DO NOT FILL ABOVE THE  
LINE INDICATED ON THE DUST BAG.  
Be sure the disposable paper filter dust bag is installed  
properly.  
5
 
How to Replace a Worn Belt  
To Adjust or Replace Brush  
WARNING: Unplug cord from  
WARNING: Unplug cord from  
electrical outlet before servicing.  
electrical outlet before servicing.  
Remove the replacement  
belt from the storage  
channel.  
To determine if the brush is  
worn, place a firm straight  
edge across the nozzle  
opening. If brush bristles  
do not extend beyond  
baseplate, brush should be  
adjusted.  
Remove the baseplate by  
removing 5 screws. Then,  
remove the belt and brush  
roll from the housing.  
Remove the door by  
removing the hold down  
screw located on side of  
power head.  
Rotate both bearing  
assemblies at ends of  
brush roll to show “OLD”  
and replace in the holding  
channels in the housing.  
Slide the door forward  
by prying open with a  
screwdriver or coin.  
NOTE: The bearing  
assembly setting marked  
“OLD” has a smooth side.  
The one marked “NEW”  
Remove the belt from the  
brush roll pulley and the  
motor drive shaft.  
has notches. When  
Rotate and match  
bearing assemblies  
rotating bearings, make  
sure both bearing  
assembly settings are the  
same and face up when  
replacing the brush roll.  
Loop the new belt over  
the motor drive shaft.  
Place the opposite end of  
the belt on the brush  
pulley. Rotate the brush  
roll three (3) complete  
revolutions to ensure that  
no part of the belt is  
Reassemble the belt and  
the baseplate and check  
bristle height above  
baseplate at each end of  
brush.  
overhanging the end of  
the motor drive shaft.  
If a previous adjustment  
has already been made  
and bristle height does not  
extend above baseplate, a  
new brush assembly  
Replace the door by  
sliding it into the groove  
at the bottom of the  
housing. Replace the  
hold down screw.  
IMPORTANT: Unless  
the brush is worn as  
indicated above,  
both bearings must  
be in the “NEW”  
position. When  
should be ordered.  
rotating, both  
bearings must be in  
the “OLD” position.  
Unmatched settings  
will cause damage  
to your machine.  
6
 
5. Many times blockage occurs  
due to a full dust bag  
F
Stuffing or Blockage  
causing dirt to back down  
the air flow system. When  
that happens, the blockage  
will be at the top of the  
system, starting in the area  
where the dust bag connects  
to the connector assembly.  
See illustration F.  
Connector  
Deflector  
Opening  
Under certain conditions it is possible to stuff or block the intake  
tube and the lower tube assembly. If your vacuum cleaner does  
not pick up properly, or makes unusual noise and the outer bag  
does not fluff up or balloon open, follow the following steps:  
WARNING: Unplug cord from electrical  
outlet before servicing.  
1. Check for blockage at the  
mouth of the intake  
opening. See illustration A.  
If there is blockage, remove  
it with long-nose pliers, a  
screwdriver or coat hanger.  
If you can not reach the  
blockage, remove  
NOTE: If the “Stuffing or Blockage” actions do not correct the  
problem, contact an ORECK authorized service center or call the  
customer service center at: 0845 603 0153.  
A
B
Intake Opening  
baseplate. See illustration B.  
2. If the blockage is not at the  
base, remove lower tube.  
See illustration C. Unhook  
retainer spring, releasing  
bottom of bag. Twist lower  
collar counterclockwise to  
slide up. Pull tube out of  
base. Check for blockage.  
If blockage is in the tube,  
remove with a coat hanger.  
3. If tube is not blocked, look  
into fan housing. See illus-  
tration D. Remove debris  
with long-nose pliers, a  
IMPORTANT: On plush and new carpets, stuffing may occur  
due to excessive fuzz and loose cuttings in the carpet.  
Stuffing could occur for the first few cleanings until all the  
loose material is removed. Due to the high efficiency of the  
cleaner, many older carpets will cause stuffing when the  
cleaner is first used on them.  
Intake Opening  
Bulb Replacement  
Retainer  
Spring  
Remove lamp housing by  
removing two (2) screws in  
the the top of the lamp  
housing. Pull burned out  
bulb from holder and  
screwdriver or coat hanger.  
4. To reassemble, check O-ring  
on tube, and replace if  
damaged. Vacuum will not  
operate properly without the  
tube O-ring. Slide O-ring to  
approximately 2" from base  
of tube. Replace tube by  
first lining up slot at base of  
tube with inner tab inside  
fan housing. Then reinsert  
tube and push down until  
the tube is seated. Make  
sure O-ring is in place  
replace with new bulb. Use  
only Oreck replacement  
parts. Reassemble lamp  
housing by replacing two  
screws in the top of the  
lamp housing. WARNING:  
Unplug cord from electrical  
outlet before servicing.  
C
Fan  
Housing  
O-ring  
Using An Oreck Fresh Air® Tab  
against fan housing  
opening. Replace and  
D
tighten collar until collar  
locking tabs are locked in  
place. See illustration E.  
Make sure collar is not cross  
threaded on housing.  
Your ORECK XL vacuum  
cleaner has a special  
E
®
Oreck Fresh Air tab  
pocket. This pocket is  
located inside the outer  
bag in the area where the  
disposable paper bag  
attaches to the intake  
tube. Insert tablet in  
pocket.  
7
 
Troubleshooting Guide  
WARNING: Unplug cord from  
electrical outlet before servicing.  
SAVE SERVICE CALLS...CHECK THESE FIRST:  
• Is the disposable filter dust bag full?  
• Are pores of filter dust bag clogged with powder or fine dust?  
• Is anything clogging the revolving brush, lower tube, intake  
opening, fan housing or connector assembly opening?  
• Is the belt in place and turning the brush?  
• Are the brush ends in the proper location?  
• Does the brush turn freely? Are hair, string or rug fibers wound  
around the brush?  
PROBLEM  
POSSIBLE SOURCE  
AREAS TO CHECK  
CLEANER  
Not plugged in  
properly.  
Be sure cleaner is  
firmly plugged  
WILL NOT RUN  
into wall outlet.  
No electricity in  
wall outlet.  
Check electrical  
source–fuse or  
circuit breaker.  
CLEANER  
Filter bag is full.  
Replace filter bag.  
See “To Replace  
Paper Filter Dust  
Bag.”  
DOES NOT PICK UP  
Nozzle or intake  
pivot clogged.  
Clear obstruction.  
Belt is broken or  
stretched.  
Replace belt.  
Brush is worn.  
See “To Adjust or  
Replace Brush.”  
Bag tube clogged. Clear obstruction.  
Bag pores are  
clogged with fine  
dust.  
Change bag.  
Impeller fan is  
broken.  
Return to Service  
Center for repair.  
Revolving brush is Check brush roll  
not even at both  
ends.  
end cards. Make  
sure words “OLD”  
or “NEW” match  
at each end.  
ALL OTHER SERVICING SHOULD BE DONE BY AN  
ORECK AUTHORIZED SERVICE CENTER.  
CALL CUSTOMER SERVICE HOT LINE  
0845 603 0153  
Whenever calling, please be sure to have your model and  
serial number from data plate.  
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks  
are owned and used under the authority of Oreck Holdings, LLC. Printed in America.  
75691-02 REV A  
08/05 ECN# R-7873  
8
 

MTX Audio Car Amplifier TC3001 User Manual
Musica Portable Speaker 52WRM User Manual
Napoleon Fireplaces Electric Heater GDS25N User Manual
Nokia Cell Phone Series 60 User Manual
NordicTrack Home Gym NTEL75062 User Manual
Omega Speaker Systems Stereo Amplifier PH 2720 PA User Manual
Omega Thermometer OS643 LS User Manual
Onkyo CD Player CR B8 User Manual
Panasonic VCR AG 2530P User Manual
Patton electronic Network Router 1000RC User Manual