Oreck Vacuum Cleaner XL2090RSM User Manual

®
S I M P L Y  
A M A Z I N G  
USERS GUIDE  
XL2090RSM  
COMMERCIAL  
HIGH SPEED UPRIGHT VACUUM  
CLEANER WITH  
®
CLEANING SYSTEM  
•IMPORTANT•  
SAVE THIS BOOKLET!  
Includes:  
• Safety Warnings  
• Warranty  
• Operating Instructions  
• Trouble Diagnosis  
• Accessories  
 
BEFORE OPERATING CLEANER,  
READ ALL INSTRUCTIONS IN  
THIS MANUAL CAREFULLY.  
IMPORTANT SAFETY  
INSTRUCTIONS  
When using an electrical appliance, basic  
precautions should always be followed,  
including the following:  
Table of Contents  
READ ALL INSTRUCTIONS BEFORE  
USING THIS VACUUM CLEANER  
Maintenance and Customer Service, Accessories,  
Grounding Instructions, Important Safety Instructions . . . . . . . page  
2
WARNING  
Warranty, Unit Specifications,Parts List,  
Assembly, Operating Instructions . . . . . . . . . . . . . . . . . . . . . . page  
To reduce the risk of fire,  
electric shock, or injury:  
3
4
5
General Information, To Replace Filter Dust Bag,  
How to Replace a Worn Belt, To Adjust or Replace Brush . . . page  
Using an Oreck Fresh Air® Tab, Stuffing or Blockage,  
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page  
• Do not leave appliance unattended when plugged in.  
Unplug from outlet when not in use and before servicing.  
• Do not use outdoors or on wet surfaces.  
• Do not operate the unit while in the upright and locked  
position.  
• Do not let the unit run while in any one stationary position  
for any period of time. Keep the unit moving while in  
operation.  
Maintenance and Customer Service  
Your Oreck vacuum cleaner is a product of precise engineering. The  
motor bearings are permanently lubricated and should not be oiled. If  
you require additional information or have problems with your Oreck  
appliance, you may call ORECK commercial customer service at:  
1-800-989-1150  
• Do not allow to be used as a toy. Close attention is  
necessary when used by or near children.  
• Use only as described in this manual. Use only  
manufacturer’s recommended attachments.  
• Do not use with damaged cord or plug. If appliance is not  
working as it should, has been dropped, damaged, left  
outdoors, or dropped into water, return it to a service  
center or call commercial customer service at:  
1-800-989-1150  
Please specify the model number and serial/code number which can be  
found on the data plate on the back of the vacuum.  
Save your sales or purchase slip. Should your ORECK appliance require  
warranty service in the U.S.A., present this slip to the Authorized Service  
Center as your proof of purchase date.  
• Do not pull or carry by cord, use cord as a handle, close  
door on cord, or pull cord around sharp edges or corners.  
Keep cord away from heated surfaces.  
• Do not run appliance over cord.  
• Do not unplug by pulling on cord. To unplug, grasp the  
plug, not the cord.  
• Do not handle plug or appliance with wet hands.  
• Do not put any object into openings. Do not use with any  
opening blocked; keep free of dust, lint, hair and anything  
that may reduce air flow.  
Accessories (Sold Separately)  
ITEM  
1.  
PART #  
®
Dust Bag, 25 Pack, Saniseal  
Hypo-Allergenic  
Dust Bag, 25 Pack, Regular  
Belts, 3 Pack  
Oreck Fresh Air® Tabs  
PK800025DW  
PK800025  
0300604  
2.  
3.  
AIRTABS  
• Keep hair, loose clothing, fingers and all parts of body  
away from openings and moving parts.  
• Do not use to pick up anything that is burning or smoking,  
such as cigarettes, matches, or hot ashes.  
• Do not use without filter bag assembly in place.  
• Turn off all controls before unplugging.  
• Use extra care when cleaning on stairs.  
• Do not use to pick up flammable or combustible liquids,  
such as gasoline or lighter fluid, or use in areas where  
they may be present.  
• Do not use appliance in an enclosed space where  
flammable, explosive or toxic vapors are given off by oil  
base paint, paint thinner, some mothproofing substances,  
or in an area where flammable dust is present.  
• Do not pick up toxic material such as chlorine bleach,  
drain cleaner, gasoline, etc. with this appliance.  
• Use caution when vacuuming over area rug edges and  
fringe.  
Grounding Instructions  
This appliance must be grounded. If it should malfunction or break  
down, grounding provides a safe path of least resistance for electrical  
current, reducing the risk of electric shock. The cord for this appliance  
has an equipment-grounding conductor and a grounding plug. It must  
only be plugged into an electrical outlet that is properly installed and  
grounded in accordance with all local codes and ordinances.  
DANGER: Improper connection of the equipment-grounding conductor  
can result in a risk of electrical shock. Check with a qualified electrician  
or service person if you are in doubt as to whether the outlet is  
grounded. If not, have a proper outlet installed by a qualified electrician.  
This appliance is for use on a nominal 120-volt circuit. It has a grounding  
plug similar to the example shown.  
Grounding Pin  
Make sure the appliance is  
connected to an outlet with the  
same configuration as the plug.  
No adapter should be used with  
this appliance.  
Grounded Outlet  
SAVE THESE INSTRUCTIONS  
For Commercial Use  
2
 
Bag Cover: XL Filter Knit, heavy duty, reinforced. Convenient pocket in  
Warranty  
back for storage of cleaning accessories and extra disposable dust bag.  
®
ORECK MANUFACTURING COMPANY: (Oreck gives you the following  
limited warranty for this product only if it was originally purchased for  
use, not resale, from Oreck or an Oreck Authorized Retail Dealer.)  
MicroSweep : Cleans bare floors without hoses, adjustments, or  
attachments.  
Oreck will repair or replace, free of charge, to the original purchaser,  
any part which is found to be defective in material or workmanship  
within six (6) months of the date of purchase. This limited warranty  
covers the revolving roller brush for thirty (30) days for commercial use  
only.  
Parts List  
To assist you in identifying components of your vacuum, the parts have  
been numbered as follows:  
This limited warranty does not cover the replacement of expendable or  
consumable parts such as carbon motor brushes, edge brushes, drive  
belts, bulbs, disposable bags and other parts subject to normal wear  
unless they are defective in material or workmanship.  
This limited warranty does not apply to any part subjected to accident,  
abuse, or alteration, misuse, damage caused by fire or act of God, the  
use of voltages other than indicated on the serial number plate of this  
product or service of this product by other than Oreck or an Oreck  
Factory Authorized Service Center.  
1
1
2
3
4
5
6
7
8
9
Handle section, upper  
Tube, lower  
11  
9
Power head  
13  
Outer bag  
Paper filter dust bag  
Power cord  
16  
5
Retaining spring  
Bag tension bar  
Zip fastener  
12  
2
4
Oreck does not authorize any person or representative to assume or  
grant any other warranty obligation with the sale of this product.  
Oreck’s limited warranty is valid only if you retain proof of purchase  
from Oreck or an Oreck Authorized Retail Dealer for this product. If you  
purchase this product from any other source, your purchase is “AS IS,”  
which means Oreck grants you no warranty, and that you, not Oreck,  
assume the entire risk of the quality and performance of this product,  
including the entire cost of any necessary servicing or repairs of any  
defects.  
10 On/off switch  
6
11 Cord hook  
12 Plastic loop / cable clamp  
13 Connector assembly  
14 Fan housing  
10  
14  
7
8
15  
Oreck’s liability for damages to you for any costs whatsoever arising out  
of this statement of limited warranty shall be limited to the amount paid  
for this product at the time of original purchase, and Oreck shall not be  
liable for any direct, indirect, consequential or incidental damages  
arising out of the use or inability to use this product.  
15 Cord assembly  
16 Handle brace  
3
Assembly  
Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not  
apply to you.  
fig. 1 Before assembling appliance, remove two screws from connector  
assembly. Remove cardboard insert by pulling upward.  
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,  
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN  
DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,  
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS  
PERIOD.  
fig. 2 With ON/OFF switch facing the front of the unit, slide upper  
handle section over matching section of the connector assembly.  
Place brace against handle and connector assembly aligning  
screw holes. Insert short screw into top hole and long screw into  
the bottom hole then tighten firmly until handle is no longer loose.  
Some states do not allow limitations on the duration of implied  
warranties, so the above limitation may not apply to you.  
Operating Instructions  
This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
Make sure disposable paper filter dust bag is in place. DO NOT operate  
the cleaner without a paper filter dust bag. Plug the power cord into an  
electrical outlet and press the On (l) - OFF(O) switch on top of base  
when ready to operate.  
Unit Specifications  
Up-Position Lock  
Power head: Width 12 1/2”, Height 4”, Leading Edge 2 1/2”.  
Self-adjusting to carpets and bare floors. Includes patented edge cleaning  
device.  
Motor: High performance precision motor, sealed ball bearing on solid  
shaft. High temperature insulation, factory lubricated for life. Heat  
dispersion system and motor cooling fan device, with self-cleaning blades.  
fig. 3 Place foot on power head and lean handle back gently to release  
lock for vacuum use. Return handle to the full upright position to  
engage lock.  
NOTE: Do not operate the unit while in the upright and locked position.  
Do not let the unit run while in any one stationary position for any period  
of time. Keep the unit moving while in operation.  
Electrical: 120 volts A.C., 4 amps, 480 watts, 60 Hz.  
Power cable: 35 feet long, Three conductor SJT type. Flexible heavy duty  
jacket.  
Operating Recommendations  
This new ORECK XL High Speed Upright is one of the finest, fastest,  
and strongest units in its class. You’ll love the way it cleans, gets under  
things, and it’s SO lightweight and easy to use.  
Sealing gaskets: Cover plate sealing gaskets absorb shock, insulate,  
resist corrosive chemicals and abrasive contact. Provide effective seal  
against dust and suction loss.  
Agitation: Full intersecting dual-row sharp helix pattern nylon bristle brush  
rotates on lifetime lubricated ball bearings. High speed alternating action  
brush cleans at approximately 6,500 rpm. Bearing holders may be rotated  
1/2 turn to extend bristle life. Dirt seals protect brush bearings from dirt  
build-up.  
The following are a few simple suggestions regarding its operation:  
1. When inserting a new disposable paper filter dust bag—FIRST  
PUFF OUT and OPEN THE BAG.  
2. When the disposable filter dust bag is full, REPLACE IT.  
3. If at any time the machine does not pick up properly or makes an  
unusual noise, STOP OPERATION and service.  
Drive belt: Most trouble-free because it’s sealed off from the dirt collection  
area. Eliminates “center” dirt path. Motor drive shaft is  
hi-carbon, stress proof steel, ground finish for minimum belt wear. Spare  
belt is stored in baseplate.  
4. Although your upright will pick up pins, paper clips, and other small  
objects, it is recommended that these be removed from the floor  
before you vacuum. Failure to do so may result in permanent  
damage to the motor suction fan and its housing.  
Super filter bag: 736 cubic inch capacity. Hypo-allergenic version is  
CELOC® Hypo-Allergenic multi-layered, high dust retention, disposable  
filter bag.  
3
 
5. WARNING: Do not use your vacuum cleaner on damp or wet  
surfaces. This will cause damage to the vacuum cleaner and is  
dangerous to the user.  
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor  
Surfaces and Polished Floor Finishes  
Use floor and floor finish manufacturer’s recommended methods of  
cleaning. The metal strip on the base of the cleaner could be damaged  
if used on concrete or abrasive surfaces, and, therefore, cause damage  
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished  
floor finishes. The roller brush may also scuff very soft finishes. Do not  
operate the unit while in the upright and locked position. Do not let the  
unit run while in any one stationary position for any period of time. Keep  
the unit moving while in operation.  
6. REPLACE THE BELT EVERY 6 MONTHS.  
7. Change the disposable filter dust bag at least once a month—  
even if it is not full! The collected dust in the dust bag can cause  
odor, attract moisture, and can affect the efficiency of the cleaner.  
8. DO NOT run the vacuum cleaner over the cord. The revolving  
brush could damage the cord.  
9. Use caution when vacuuming over area rug edges and fringe.  
General Information  
To Replace Filter Dust Bag  
WARNING: Unplug cord from electrical  
outlet before servicing.  
The performance of your new cleaner greatly depends upon care and  
maintenance. The instructions in this manual will guide you in  
performing basic care and maintenance. To obtain the most satisfying  
years of service read the instructions and keep them handy for future  
reference.  
BAG REMOVAL:  
fig. 4 Unzip outer bag completely.  
fig. 5 Pull bag cardboard collar to release bag from connector.  
BAG INSTALLATION:  
Disposable Paper Filter Dust Bags  
Disposable paper filter dust bags play a very important role in the  
efficiency of your ORECK vacuum cleaner. The purpose of the filter bag  
is to trap dirt, but at the same time it must be porous enough to allow air  
to pass through. If the filter bag becomes clogged, no air can pass  
through the cleaner and cleaning cannot take place, regardless of the  
cleaner’s power.  
fig. 6 Hook bottom of bag collar opening under lip "B" of connector  
assembly. Pull up on bag collar and snap over lip "A" of  
connector.  
fig. 7 Press on edges of bag collar to insure bag is completely  
installed.  
To keep your cleaner operating at maximum efficiency, change the dust  
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE  
DUST BAG.  
IMPORTANT: Check to make sure bag collar is behind lips "A" and "B".  
If it is not, dust will leak into outer bag. When filter bag is in place,  
close outer bag with zipper fastener.  
Be sure the disposable paper filter dust bag is installed properly.  
All paper dust bags are not the same. Your ORECK disposable  
dust bags have been designed to be used with the ORECK cleaner.  
Using bags other than genuine ORECK disposable bags will affect  
the cleaning ability of your cleaner and could cause damage to it.  
How to Replace a Worn Belt  
WARNING: Unplug cord from electrical  
outlet before servicing.  
The Belt  
fig. 8 Remove the replacement belt from the storage channel.  
The belt on your vacuum cleaner controls the speed of the revolving  
brush and is very important for the effective operation of the cleaner. If  
the belt becomes stretched or cut, it will cause the revolving brush to  
stop completely or slow down. See instructions in the manual for  
replacing belt.  
fig. 9 Remove the door by removing the hold down screw located on  
side of power head.  
fig. 10 Slide the door forward by prying open with a screwdriver or  
coin.  
An extra belt is stored in the baseplate of your cleaner. When  
buying replacement belts, use ONLY ORECK genuine belts. Belts  
other than Oreck belts will not operate the revolving brush  
correctly and may create undue stress which will cause damage to  
the motor and brush bearings.  
fig. 11 Remove the belt from the motor drive shaft and brush roll  
pulley.  
fig. 12 Loop the new belt over the motor drive shaft. Place the  
opposite end of the belt on the brush roll pulley. Rotate the  
brush roll three (3) complete revolutions to ensure that no part  
of the belt is overhanging the end of the motor drive shaft.  
Lubrication  
The vacuum cleaner motor bearings are factory lubricated and sealed.  
Further lubrication is not required.  
fig. 10 Replace the door by sliding it into the groove at the bottom of  
the housing.  
General Cleaner Care  
fig. 9 Replace the hold down screw and tighten.  
At least once a month, check for  
and remove excessive lint, string or  
hair from revolving brush.  
To Adjust or Replace Brush  
WARNING: Unplug cord from electrical  
outlet before servicing.  
Wipe the outside of the cleaner with  
a damp cloth. Also, clean the  
connector deflector assembly area,  
base of cleaner and fan housing  
area. If there is dust in the outer  
bag, vacuum it or shake it out.  
fig. 13 To determine if the brush is worn, place a firm straight edge  
across the nozzle opening. If brush bristles do not extend  
beyond baseplate, brush should be adjusted.  
fig. 14 Remove the baseplate by removing 5 screws.  
A little preventative maintenance will  
keep your cleaner looking new and  
will ensure continued cleaning effec-  
tiveness.  
fig. 15 Remove the belt and brush roll from the housing.  
fig. 16 Rotate both bearing assemblies at ends of brush roll to show  
"OLD" and replace in the holding channels in the housing.  
NOTE: The bearing assembly setting marked “OLD” has a smooth side  
on the end card. The one marked “NEW” is notched on the end card.  
When rotating bearings, make sure both bearing assembly settings are  
the same and face up when replacing the brush roll.  
fig. 13 Reassemble the belt and the baseplate and check bristle height  
above baseplate at each end of brush.  
If a previous adjustment has already been made and bristle height does  
not extend above baseplate, a new brush assembly should be ordered.  
4
 
IMPORTANT: Unless the brush is worn as indicated above, both  
bearings must be in the “NEW” position. When rotating, both  
bearings must be in the “OLD” position. Unmatched settings will  
cause damage to your machine.  
Troubleshooting Guide  
WARNING: Unplug cord from electrical  
outlet before servicing.  
®
Using An Oreck Fresh Air Tab  
SAVE SERVICE CALLS...CHECK THESE FIRST:  
• Is the disposable filter dust bag full?  
• Are pores of filter dust bag clogged with powder or fine dust?  
fig. 17 Your ORECK XL vacuum cleaner has a special Oreck Fresh  
Air® tab pocket. This pocket is located inside the outer bag in  
the area where the disposable paper bag attaches to the intake  
tube. Insert tablet in pocket if desired.  
• Is anything clogging the revolving brush, lower tube, intake opening,  
fan housing or connector assembly opening?  
• Is the belt in place and turning the brush?  
• Are the brush ends in the proper location?  
Stuffing or Blockage  
IMPORTANT: On plush and new carpets, stuffing may occur inside the  
the intake tube and the lower tube assembly. This is due to excessive fuzz  
and loose cuttings in the carpet. Stuffing could occur for the first few  
cleanings until all the loose material is removed. Due to the high efficiency  
of the cleaner, many older carpets will cause stuffing when the cleaner is  
first used on them. If your vacuum cleaner does not pick up properly, or  
makes unusual noise and the outer bag does not fluff up or balloon open,  
follow these steps:  
• Does the brush turn freely? Are hair, string or rug fibers wound around  
the brush?  
PROBLEM  
CLEANER  
POSSIBLE SOURCE  
AREAS TO CHECK  
Not plugged in  
properly.  
Be sure cleaner is  
firmly plugged into  
wall outlet.  
WILL NOT RUN  
WARNING: Unplug cord from electrical  
outlet before servicing.  
No electricity in wall  
outlet.  
Check electrical  
source–fuse or  
circuit breaker.  
fig. 18 Check for blockage at the mouth of the intake opening. If there  
is blockage, remove it with long-nose pliers, a screwdriver or  
coat hanger. If you can not reach the blockage, remove (fig. 19).  
CLEANER  
DOES NOT PICK UP  
Filter bag is full.  
Replace filter bag. See  
To Replace Paper  
Filter Dust Bag.”  
fig. 20 If the blockage is not at the base, remove lower tube. Unhook  
retainer spring, releasing bottom of bag.  
fig. 21 Twist lower collar counterclockwise to slide up. Pull tube out of  
Nozzle or intake  
pivot clogged.  
Clear obstruction.  
Replace belt.  
base.  
fig. 22 Check for blockage. If blockage is in the tube, remove with a  
coat hanger.  
Belt is broken or  
stretched.  
fig. 23 If tube is not blocked, look into fan housing. Remove debris  
with long-nose pliers, a screwdriver or coat hanger.  
fig. 21 To reassemble, check O-ring on tube, and replace if damaged.  
Vacuum will not operate properly without the tube O-ring. Slide  
O-ring to approximately 2" from base of tube. Replace tube by  
first lining up slot at base of tube with inner tab inside fan  
housing. Then reinsert tube and push down until the tube is  
seated. Make sure O-ring is in place against fan housing  
opening. Replace and tighten collar until collar locking tabs are  
locked in place.  
Brush is worn.  
See “To Adjust or  
Replace Brush”  
Bag tube clogged.  
Clear obstruction.  
Change bag.  
Bag pores are  
clogged with fine  
dust.  
fig. 24 Make sure collar is not cross threaded on housing. Reattach  
bag spring (fig. 20).  
Impeller fan is  
broken.  
Return to Service  
Center for repair.  
fig. 25 Many times blockage occurs due to a full dust bag causing dirt  
to back down the air flow system. When that happens, the  
blockage will be at the top of the system, starting in the area  
where the dust bag connects to the connector assembly.  
Revolving brush is  
not even at both  
ends.  
Check brush roll end  
cards. Make sure  
words “old” or “new”  
match at each end.  
NOTE: If the above actions do not correct the problem, contact an  
Oreck authorized service center or call the commercial customer service  
center. USA: 1-800-989-1150  
ALL OTHER SERVICING SHOULD BE DONE BY AN  
ORECK AUTHORIZED SERVICE CENTER.  
CALL COMMERCIAL CUSTOMER SERVICE  
1-800-989-1150  
Whenever calling, please be sure to have your model and serial  
number from data plate.  
5
 
6
 
75376-07 REV B  
05/05 ECN# R-8018  
©2005 Oreck Holdings, LLC. All Rights Reserved. All word marks, logos, registered trademarks and product configurations are  
owned and used under the authority of Oreck Holdings, LLC.  
 

Miele Washer Dryer W 4840 User Manual
Mr Handsfree Headphones Blue Chameleon User Manual
MTD Yard Vacuum 245 675 000 User Manual
NEC Projection Television GT2000 GT2000R User Manual
NEC Projector LT155 User Manual
NeumannBerlin Microphone KMS 104 User Manual
NordicTrack Treadmill NTL149052 User Manual
Novatel Card Game OM 20000041 User Manual
Omnitron Systems Technology Network Card MUX DEMUX User Manual
Panasonic Camera Lens H PS45175 User Manual