®
S I M P L Y
A M A Z I N G
USER’S GUIDE
XL2800HAY
HIGH SPEED UPRIGHT VACUUM
CLEANER WITH
®
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
ACCESSORIES
Maintenance and
Customer Service
SOLD SEPARATELY
USA: 1-800-989-3535
CANADA: 1-888-676-7325
Your ORECK vacuum cleaner is a product of precise engineering.
The motor bearings are permanently lubricated and should not be
oiled. If you require additional information or have problems with
your ORECK appliance, you may call ORECK customer service at:
ITEM
PART NUMBER
1. Dust Bag, 8 Pack
®
Saniseal , ACDS,
CCPK8DW
-
-
In USA
1800989-3535
Hypo-Allergenic
2. Belts, 3 Pack
3. Light Bulb
In Canada 1-888-676-7325
0300604
00965-0019
Please specify the model number and serial/code number which
can be found on the data plate on the back of the vacuum.
®
4. Oreck Fresh Air Tabs
AIRTABS
ESP-110
Save your sales or purchase slip. Should your ORECK appliance
require warranty service in the U.S.A., present this slip to the
Authorized Service Center as your proof of purchase date or, in
Canada, call customer service.
5. Headphones
Warranty
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company
gives you the following limited warranty for this product only if it was origi-
nally purchased for residential use, not resale, from Oreck or an Oreck
Authorized Retail Dealer.)
Assembly
To assist you in identifying
components of your vacuum,
the parts have been numbered
10
11
9
Oreck will repair or replace, free of charge, to the original purchaser, any
part which is found to be defective in material or workmanship within three
(3) years of the date of purchase; ten (10) years on housing. This limited
warranty applies to normal domestic use. Any commercial use of this
product will void this limited warranty. This limited warranty covers the
revolving roller brush for one (1) year for residential use only.
as follows
:
1
1 Handle section, upper
2 Tube, lower
3 Power head
4 Outer bag
This limited warranty does not cover the replacement of expendable or
consumable parts such as carbon motor brushes, edge brushes, drive belts,
bulbs, disposable bags and other parts subject to normal wear unless they
are defective in material or workmanship.
12
5
4
5 Paper filter dust bag
6 Power cord
7 Retaining spring
8 Bag tension bar
9 Zip fastener
13
6
2
This limited warranty does not apply to any part subjected to accident,
abuse, commercial use, alteration, misuse, damage caused by act of God,
the use of voltages other than indicated on the serial number displayed on
this product or service of this product by other than Oreck or a partici-
pating Factory Authorized Service Center.
15
7
10 On/off switch
11 Cord dump
14
8
Oreck does not authorize any person or representative to assume or grant
any other warranty obligation with the sale of this product.
12 Plastic loop/cable clamp
13 Connector assembly
14 Fan housing
Oreck’s limited warranty is valid only if you retain proof of purchase from
Oreck or an Oreck Authorized Retail Dealer for this product. If you
purchase this product from any other source, your purchase is “AS IS,”
which means Oreck grants you no warranty, and that you, not Oreck,
assume the entire risk of the quality and performance of this product,
including the entire cost of any necessary servicing or repairs of any
defects.
3
15 Cord assembly
Oreck’s liability for damages to you for any costs whatsoever arising out of
this statement of limited warranty shall be limited to the amount paid for this
product at the time of original purchase, and Oreck shall not be liable for
any direct, indirect, consequential or incidental damages arising out of the
use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation or exclusion may not apply to
you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
WARRANTY PERIOD, AND NO WARRANTIES, WHETHER EXPRESS OR
IMPLIED, WILL APPLY AFTER THIS PERIOD.
Some states do not allow limitations on the duration of implied warranties,
so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
3
Upper
Handle
1
6
2
3
8
4
5
Plug (Cord Assembly)
Connector
Assembly
7
9
10
Cord dump
NOTE: Do not operate the unit while in the upright and locked
position. Do not let the unit run while in any one stationary
position for any period of time. Keep the unit moving while in
operation.
11
12
For Easy Power Cord Storage
fig. 6
Wrap power cord around cord dump on Helping
®
Hand handle and cord hook on connector.
Secure to "U" shaped part on plug
ENFONCEZ JUSQU’À
TNE DEN RBNUE RIUT
fig. 7
To release cord, twist cord dump located on
PRSEIHENO ATS
A
HCUSE ARNU
HC AIUQSDDO CJUSIE
ÓN
®
Helping Hand handle 1/2 turn. Slide cord off
handle.
fig. 1
Before assembling appliance, remove two screws
To Replace Filter
Dust Bag
from the connector assembly. Remove cardboard
insert by pulling upward.
fig. 2
With ON/OFF switch facing the front of the unit,
WARNING: Unplug cord from electrical outlet
before servicing.
slide upper handle section over matching section
of the connector assembly. Insert short screw into
top hole and long screw into the bottom hole then
tighten firmly until handle is no longer loose.
fig. 8
fig. 9
Unzip outer bag completely.
Pull bag cardboard collar to release bag dock
fig. 3
Attach cord to cord clip by pressing cord above
door from connector. Bag dock door will hinge
downward.
and below clip ensuring the cord is fully rested in
clip.
fig. 10 Gently pull bag cardboard collar upward out of
the bag dock. Dust seal will close automatically.
fig. 4
Insert plug on cord assembly into handle.
General Information
Bag Installation
Make sure disposable paper filter dust bag is in place. DO
NOT operate the cleaner without a paper filter dust bag. Plug
the power cord into an electrical outlet and press the On (l) -
OFF(O) switch on Helping Handle Assembly when ready to
operate.
fig. 11 Slide the cardboard collar completely onto bag
dock door.
fig. 12 Firmly push bag dock door with both thumbs on
indication point until it snaps.
Up-Position Lock
fig. 5
Place foot on power head and lean handle back
gently to release lock for vacuum use. Return
handle to the full upright position to engage lock.
4
Operating Instructions
To Operate
change the dust bag frequently. DO NOT FILL ABOVE THE
LINE INDICATED ON THE DUST BAG.
Make sure the disposable paper filter dust bag is in place.
DO NOT operate the cleaner without a paper filter dust bag.
Plug the power cord into an electrical outlet. Choose from the
low and high speed settings by pressing the ON/LOW (l)
ON/HIGH (ll) - OFF (O) switch on handle assembly when
ready to operate.
Be sure the disposable paper filter dust bag is installed
properly.
All paper dust bags are not the same. Your ORECK
disposable dust bags have been designed to be used with
the ORECK cleaner. Using bags other than genuine ORECK
Type CC disposable bags will affect the cleaning ability of
your cleaner and could cause damage to it.
General Information
The performance of your new cleaner greatly depends upon
care and maintenance. The instructions in this manual will
guide you in performing basic care and maintenance. To
obtain the most satisfying years of service read the instructions
and keep them handy for future reference.
The Belt
The belt on your vacuum cleaner controls the speed of the
revolving brush and is very important for the effective
operation of the cleaner. If the belt becomes stretched or cut,
it will cause the revolving brush to stop completely or slow
down. See instructions in the manual for replacing belt.
Operating Recommendations
This new ORECK XL High-Speed Upright is one of the finest,
fastest, and strongest units in its class. You’ll love the way it
cleans, gets under things, and it’s SO lightweight and easy to
use.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts.
Belts other than ORECK belts will not operate the revolving
brush correctly and may create undue stress which will cause
damage to the motor and brush bearings. Using belts other
than ORECK belts will void the warranty.
The following are a few simple suggestions regarding its
operation:
1. When inserting a new disposable paper filter dust
bag—FIRST PUFF OUT and OPEN THE BAG.
2. When the disposable filter dust bag is full, REPLACE IT.
3. If at any time the machine does not pick up properly
or makes an unusual noise, STOP OPERATION and
service.
Lubrication
The vacuum cleaner motor bearings are factory lubricated
and sealed. Further lubrication is not required.
4. Although your upright will pick up pins, paper clips,
and other small objects, it is recommended that these
be removed from the floor before you vacuum. Failure
to do so may result in permanent damage to the motor
suction fan and its housing.
5. WARNING: Do not use your vacuum cleaner on
damp or wet surfaces. This will cause damage to the
vacuum cleaner and is dangerous to the user. Damage
caused by use on wet or damp surfaces is not covered
under warranty.
6. REPLACE THE BELT EVERY 6 MONTHS.
7. Change the disposable filter dust bag at least once a
month—even if it is not full! The collected dust in the
dust bag can cause odor, attract moisture, act as a
breeding area and can affect the efficiency of the
cleaner.
General Cleaner Care
At least once a month, check
for and remove excessive lint,
string or hair from revolving
brush.
Wipe the outside of the
cleaner with a damp cloth.
Also, clean the connector
deflector assembly area, base
of cleaner and fan housing
area. If there is dust in the
outer bag, vacuum it or shake
it out.
A little preventative maintenance will keep your cleaner
looking new and will ensure continued cleaning effec-
tiveness.
8. DO NOT run the vacuum cleaner over cord. The
revolving brush could damage the cord.
9. Use caution when vaccuming over area rug edges
and fringe
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile,
etc.) Floor Surfaces and Polished Floor Finishes
Use floor and floor finish manufacturer’s recommended
methods of cleaning. The metal strip on the base of the
cleaner could be damaged if used on concrete or abrasive
surfaces, and, therefore, cause damage to wood floors, soft
(vinyl, asphalt tile, etc.) floor surfaces and polished floor
finishes. The roller brush may also scuff very soft finishes. Do
not operate the unit while in the upright and locked position.
Do not let the unit run while in any one stationary position for
any period of time. Keep the unit moving while in operation.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role
in the efficiency of your ORECK vacuum cleaner. The purpose
of the paper bag is to trap dirt, but at the same time it must
be porous enough to allow air to pass through. If the paper
bag becomes clogged, no air can pass through the cleaner
and cleaning cannot take place, regardless of the cleaner’s
power.
To keep your cleaner operating at maximum efficiency,
5
Celoc® Hypo-Allergenic Filter System
Troubleshooting Guide
The CELOC SMMS outer bag of your vacuum cleaner is high
filtration medical material designed to filter the smallest of
dust particles. It is important that the inside of the outer bag
be cleaned. Turned inside out, vacuum the inside of the outer
bag or hand wash, with warm water and air dry. For best
results, the CELOC SMMS outer bag should be replaced
once a year. The CELOC layered disposable inner dust bag
must be replaced once a month even if it is not full. Change it
more often if it is used in extremely dirty areas. Increase the
cleaning power of your vacuum by changing the bag often.
WARNING: Unplug cord from
electrical outlet before servicing.
SAVE SERVICE CALLS...CHECK THESE FIRST:
• Is the disposable filter dust bag full?
• Are pores of filter dust bag clogged with powder or fine dust?
• Is anything clogging the revolving brush, lower tube, intake
opening, fan housing or connector assembly opening?
• Is the belt in place and turning the brush?
• Are the brush ends in the proper location?
• Does the brush turn freely? Are hair, string or rug fibers wound
around the brush?
Operating Instructions
for the Radio Handle
PROBLEM
POSSIBLE SOURCE
AREAS TO CHECK
CLEANER
Not plugged in
properly.
Be sure cleaner is
firmly plugged
WILL NOT RUN
into wall outlet.
No electricity in
wall outlet.
Check electrical
source–fuse or
circuit breaker.
Plug not firmly in
Plug firmly in
handle assembly. handle assembly.
CLEANER
Filter bag is full.
Replace filter bag.
See “To Install
Paper Filter Dust
Bag.”
DOES NOT PICK UP
Nozzle or intake
pivot clogged.
Clear obstruction.
Belt is broken or
stretched.
Replace belt.
Brush is worn.
See “To Adjust
or Replace Brush.”
ON/OFF SWITCH: Located on headphone
cord. Controls power to the headphone.
Bag tube clogged. Clear obstruction.
VOLUME: Located on headphone cord.
Adjust volume by turning dial.
Bag pores are
clogged with fine
dust.
Change bag.
WARNING: Do not press panel buttons with finger nails. Damage can
occur. Use finger surface only.
Impeller fan is
broken.
Return to Service
Center for repair.
POWER INDICATOR: Lights when power is present.
SCAN BUTTON: Searches to the next available station signal.
Revolving brush is Check brush roll
RESET BUTTON: Returns station signal search to beginning of FM
not even at both
ends.
end cards. Make
sure words “old”
or “new” match at
each end.
frequency range. RESET must be pressed to restart a station signal scan.
HEADPHONES: Insert headphone jack here.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
CALL CUSTOMER SERVICE HOT LINE
US: 1-800-989-3535
CANADA: 1-888-676-7325
Whenever calling, please be sure to have your model and
serial number from data plate.
6
How to Replace a Worn Belt
To Adjust or Replace Brush
WARNING: Unplug cord from
WARNING: Unplug cord from
electrical outlet before servicing.
electrical outlet before servicing.
Remove the replacement
belt from the storage
channel.
To determine if the brush is
worn, place a firm straight
edge across the nozzle
opening. If brush bristles
do not extend beyond
baseplate, brush should be
adjusted.
Remove the baseplate by
removing 5 screws. Then,
remove the belt and brush
roll from the housing.
Remove the door by
removing the hold down
screw located on side of
power head.
Rotate both bearing assem-
blies at ends of brush roll
to show “old” and replace
in the holding channels in
the housing.
Slide the door forward
by prying open with a
screwdriver or coin.
NOTE: The bearing
assembly setting marked
“OLD” has a smooth side.
The one marked “NEW”
has a notch. When
Remove the belt from the
brush roll pulley and the
motor drive shaft.
Rotate and match bearing
rotating bearings, make
assemblies
sure both bearing
assembly settings are the
same and face up when
replacing the brush roll.
Loop the new belt over
the motor drive shaft.
Place the opposite end of
the belt on the brush roll
pulley.
Reassemble the belt and
the baseplate and check
bristle height above
baseplate at each end of
brush.
Rotate the brush roll three
(3) complete revolutions
to ensure that no part of
the belt is overhanging
the end of the motor
drive shaft.
If a previous adjustment
has already been made
and bristle height does not
IMPORTANT: Unless
extend above baseplate, a
the brush is worn as
new brush assembly
should be ordered.
indicated above,
both bearings must
Replace the door by
sliding it into the groove
at the bottom of the
housing. Replace the
hold down screw.
be in the “new”
position. When
rotating, both
bearings must be in
the “old” position.
Unmatched settings
will cause damage
to your machine.
7
4. To reassemble, check O-ring
on tube, and replace if
Bulb Replacement
damaged. Vacuum will not
operate properly without the
tube O-ring. Slide O-ring to
approximately 2" from base
of tube. Replace tube by first
lining up slot at base of tube
with inner tab inside fan
Fan
Housing
O-ring
WARNING: Unplug cord from
electrical outlet before servicing.
• Remove lamp housing
housing. Then reinsert tube
and push down until the tube
is seated. Make sure O-ring is
in place against fan housing
opening. Replace and tighten
collar until collar locking tabs
are locked in place. See
illustration E. Make sure
collar is not cross threaded
on housing.
by removing two (2)
screws in the the top of
the lamp housing.
D
E
• Pull burned out bulb
from holder and replace
with new bulb. Use only
Oreck replacement
parts.
5. Many times blockage occurs
due to a full dust bag causing
dirt to back down the air flow
system. When that happens,
the blockage will be at the
top of the system, starting in
the area where the dust bag
connects to the connector
assembly. See illustration F.
• Replace lamp housing
by replacing two screws
in the top of the lamp
housing.
F
Connector
Deflector
Opening
Stuffing or Blockage
Under certain conditions it is possible to stuff or block the intake
tube and the lower tube assembly. If your vacuum cleaner does
not pick up properly, or makes unusual noise and the outer bag
does not fluff up or balloon open, follow the following steps:
WARNING: Unplug cord from electrical
outlet before servicing.
NOTE: If the above actions do not correct the problem, contact
1. Check for blockage at the
mouth of the intake
an ORECK authorized service center or call the customer service
center.
US: 1-800-989-3535
opening. See illustration A.
If there is blockage, remove
it with long-nose pliers, a
screwdriver or coat hanger.
If you can not reach the
CANADA: 1-888-676-7325
IMPORTANT: On plush and new carpets, stuffing may occur
due to excessive fuzz and loose cuttings in the carpet.
Stuffing could occur for the first few cleanings until all the
loose material is removed. Due to the high efficiency of the
cleaner, many older carpets will cause stuffing when the
cleaner is first used on them.
blockage, remove
A
B
Intake Opening
baseplate. See illustration B.
2. If the blockage is not at the
base, remove lower tube.
See illustration C. Unhook
retainer spring, releasing
bottom of bag. Twist lower
collar counterclockwise to
slide up. Pull tube out of
base. Check for blockage.
If blockage is in the tube,
remove with a coat hanger.
3. If tube is not blocked, look
into fan housing. See
Using An Oreck Fresh Air® Tab
Intake Opening
Your ORECK XL vacuum
cleaner has a special
Retainer
Spring
®
FRESH AIR tab pocket.
illustration D. Remove debris
with long-nose pliers, a
screwdriver or coat hanger.
This light-colored pocket is
located inside the vinyl
bag in the area where the
paper disposable bag
attaches to the intake
tube. Insert tablet in
pocket.
C
©2008 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC.
75451-04 REV D
03/08 ECN# R-8997
|