Panasonic Network Card 2SC5950 User Manual

This product complies with the RoHS Directive (EU 2002/95/EC).  
Transistors  
2SC5950  
Silicon NPN epitaxial planar type  
For general amplification  
Unit: mm  
–0.05  
Complementary to 2SA2122  
+0.10  
+0.1  
–0.0  
0.15  
0.3  
3
Features  
High forward current transfer ratio hFE  
Smini typ package, allowing downsizing of the equipment and automatic  
insertion through the tape packing  
1
2
(0.65) (0.65)  
Absolute Maximum Ratings T
a
= 25
°
C  
1.3±0.1  
Parameter  
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector current  
Symbol  
VCBO  
VCEO  
VEBO  
IC  
Rating  
Unit  
V
2.0±0.2  
60  
10°  
50  
7
V
V
100  
mA  
mA  
mW  
°
C  
1: Base  
2: Emitter  
Peak collector current  
ICP  
200  
3: Collector  
SMini3-G1 Package  
Collector power dissipation  
Junction temperature  
PC  
150  
Marking Symbol: 7M  
Tj  
150  
Storage temperature  
T
stg  
55 to +150  
°
C  
Electrical Characteristics T
a
= 25
°
C±3
°
C  
Parameter  
Symbol  
Conditions  
Min  
60  
50  
7
Typ  
Max  
Unit  
V
Collector-base voltage (Emitter open)  
Collector-emitter voltage (Base open)  
Emitter-base voltage (Collector open)  
Collector-base cutoff current (Emitter open)  
Collector-emitter cutoff current (Base open)  
Forward current transfer ratio  
VCBO IC = 10 µA, I
E
= 0  
VCEO IC = 2 mA, IB = 0  
VEBO I
E
= 10 µA, IC = 0  
V
V
ICBO  
ICEO  
hFE  
VCB = 20 V, I
E
= 0  
VCE = 10 V, IB = 0  
VCE = 10 V, IC = 2 mA  
0.1  
100  
460  
0.3  
µA  
µA  
160  
Collector-emitter saturation voltage  
Transition frequency  
VCE(sat) IC = 100 mA, IB = 10 mA  
0.1  
V
fT  
VCB = 10 V, I
E
2 mA, f = 200 MHz  
VCB = 10 V, IE = 0, f = 1 MHz  
100  
MHz  
Collector output capacitance  
Cob  
2.2  
pF  
(Common base, input open circuited)  
Note) Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7030 measuring methods for transistors.  
Publication date: May 2005  
SJC00333AED  
1
 
Request for your special attention and precautions in using the technical information and  
semiconductors described in this book  
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and  
regulations of the exporting country, especially, those with regard to security export control, must be observed.  
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples  
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other  
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other  
company which may arise as a result of the use of technical information described in this book.  
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office  
equipment, communications equipment, measuring instruments and household appliances).  
Consult our sales staff in advance for information on the following applications:  
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support  
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-  
ucts may directly jeopardize life or harm the human body.  
Any applications other than the standard applications intended.  
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-  
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product  
Standards in advance to make sure that the latest specifications satisfy your requirements.  
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions  
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute  
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any  
defect which may arise later in your equipment.  
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure  
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire  
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.  
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,  
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which  
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.  
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita  
Electric Industrial Co., Ltd.  
 

Multi Tech Systems Fax Machine DT101 User Manual
National Instruments Electronic Accessory NI 845x User Manual
NEC Computer Monitor FP1375X User Manual
Nextar GPS Receiver X3B User Manual
Nortel Networks Cordless Telephone Portable Telephone User Manual
Oki Printer 3037 User Manual
Olive Media Products Home Theater Server 4 User Manual
Omega Beverage Dispenser B2100 User Manual
Panasonic Camcorder AG AC130P User Manual
Panasonic DVD Player CQ DX100W User Manual