Panasonic Kx Tg1855 User Manual

Operating Instructions  
Digital Cordless Answering System  
Model No.  
KX-TG1855AL  
KX-TG1857AL  
KX-TG1855  
This unit is Caller ID compatible. To display the caller’s  
phone number, you must subscribe to Caller ID service.  
Charge the batteries for about 7 hours before initial use.  
Please read these operating instructions before using the unit and save  
them for future reference.  
Preparation  
Introduction  
Thank you for purchasing a new Panasonic digital cordless phone.  
For your future reference  
Attach or keep original receipt to assist with any repair under warranty.  
Serial No. (found on the bottom of the base unit)  
Date of purchase  
Name and address of dealer  
Note:  
L In the event of problems, you should contact your equipment supplier in the first  
instance.  
Your phone  
KX-TG1855  
KX-TG1857  
3
   
Preparation  
Accessory information  
Supplied accessories  
No. Accessory items  
Quantity  
KX-TG1855 KX-TG1857  
1
AC adaptor for base unit  
(Part No. PQLV207AL)  
1
1
*1  
2
3
Telephone line cord  
1
2
1
4
Rechargeable batteries AAA (R03) size  
(Part No. HHR-55AAAB)  
*2  
4
5
6
Handset cover  
1
2
1
1
Charger (Part No. PQLV30055Z)  
AC adaptor for charger (Part No. PQLV209AL)  
*1 The telephone line cord comes connected with the telephone plug.  
*2 The handset cover comes attached to the handset.  
1
2
3
4
5
6
Additional/replacement accessories  
Please contact your nearest Panasonic dealer for sales information.  
No. Model No. Description  
*1  
1
HHR-4EPT/2B  
2 rechargeable nickel metal hydride (Ni-MH) batteries,  
AAA (R03) size  
2
3
4
5
KX-TGA185AZ  
Additional Digital Cordless Handset  
Wall-Mounting Adaptor  
Belt Clip  
KX-TCA727EX  
KX-TCA718EX  
KX-A272AL  
DECT repeater  
*1 Replacement batteries may have a different capacity from that of the supplied  
batteries.  
3
4
4
             
Preparation  
Warning:  
L To prevent the risk of electrical shock,  
do not expose this product to rain or  
any other type of moisture.  
Important information  
General  
L Unplug this product from power  
outlets if it emits smoke, an abnormal  
smell, or makes unusual noise. These  
conditions can cause fire or electric  
shock. Confirm that smoke has  
L Use only the AC adaptor supplied with  
this product, noted on page 4.  
L Do not connect the AC adaptor to any  
AC outlet other than a standard  
220–240 V AC outlet.  
stopped emitting and contact an  
authorised service centre.  
L This product is unable to make calls  
when:  
L Do not spill liquids (detergents,  
cleansers, etc.) onto the telephone  
line cord plug, or allow it to become  
wet at all. This may cause a fire. If the  
telephone line cord plug becomes  
wet, immediately pull it from the  
telephone wall jack, and do not use.  
L Do not place or use this product near  
automatically controlled devices such  
as automatic doors and fire alarms.  
Radio waves emitted from this product  
may cause such devices to  
– the portable handset battery(ies)  
need recharging or have failed.  
– there is a power failure.  
– the key lock feature is turned on.  
L Do not open the base unit, charger, or  
handset other than to replace the  
battery(ies).  
L This product should not be used near  
emergency/intensive care medical  
equipment and should not be used by  
people with pacemakers.  
malfunction resulting in an accident.  
L Regularly remove any dust, etc. from  
the AC adaptor/power plug by pulling  
it from the power outlet, then wiping  
with a dry cloth. Accumulated dust  
may cause an insulation defect from  
moisture, etc. resulting in a fire.  
L Do not damage the power cord/plug.  
This may cause a short circuit, electric  
shock, and/or fire.  
L Care should be taken that objects do  
not fall onto, and liquids are not spilled  
into, the product. Do not subject this  
product to excessive smoke, dust,  
mechanical vibration or shock.  
Environment  
L Do not use this product near water.  
L This product should be kept away  
from heat sources such as radiators,  
cookers, etc. It should also not be  
placed in rooms where the  
temperature is less than 5 °C or  
greater than 40 °C.  
L It is advised not to use the equipment  
at a refuelling point. Users are  
reminded to observe restrictions on  
the use of radio equipment in fuel  
depots, chemical plants or where  
blasting operations are in progress.  
L Do not touch the plug with wet hands.  
L The AC adaptor is used as the main  
disconnect device. Ensure that the AC  
outlet is installed near the product and  
is easily accessible.  
Battery caution  
L We recommend using the battery(ies)  
noted on page 4. Use only  
rechargeable battery(ies).  
L Do not mix old and new batteries.  
5
   
Preparation  
L Do not dispose of the battery(ies) in a  
fire, as they may explode. Check with  
local waste management codes for  
special disposal instructions.  
– Unplug the telephone line cord from  
the phone socket.  
– Unplug the AC adaptor from the AC  
power outlet.  
L Do not open or mutilate the  
L No “000” or other calls can be made  
from this device during a mains power  
failure.  
battery(ies). Released electrolyte  
from the battery(ies) is corrosive and  
may cause burns or injury to the eyes  
or skin. The electrolyte may be toxic if  
swallowed.  
L The earpiece on the handset is  
magnetised and may retain small  
metallic objects.  
L Exercise care when handling the  
battery(ies). Do not allow conductive  
materials such as rings, bracelets or  
keys to touch the battery(ies),  
otherwise a short circuit may cause  
the battery(ies) and/or the conductive  
material to overheat and cause burns.  
L Charge the battery(ies) provided with  
or identified for use with this product  
only in accordance with the  
L This equipment has been tested and  
found to comply with AS/NZS  
CISPR22: 2004 limits for  
electromagnetic interference. Any  
modifications to any part of the system  
or to any peripherals may void the  
EMC compliance of the system or the  
peripherals.  
Notice for product disposal, transfer,  
or return  
instructions and limitations specified  
in this manual.  
L This product can store your  
private/confidential information. To  
protect your privacy/confidentiality, we  
recommend that you erase the  
information such as phonebook or  
caller list entries from the memory  
before you dispose, transfer or return  
the product.  
L Only use a compatible base unit (or  
charger) to charge the battery(ies). Do  
not tamper with the base unit (or  
charger). Failure to follow these  
instructions may cause the  
battery(ies) to swell or explode.  
Notice  
L Please ensure that a separate  
telephone, not dependent on local  
power, is available for emergency use.  
L This equipment will be inoperable  
when mains power fails.  
Information on Disposal in other  
Countries outside the European  
Union  
L When a failure occurs which results in  
the internal parts becoming  
accessible, disconnect the power  
supply cord immediately and return  
this unit to an authorised service  
centre.  
This symbol is only valid in the European  
Union. If you wish to discard this  
product, please contact your local  
authorities or dealer and ask for the  
correct method of disposal.  
L To minimise the possibility of lightning  
damage, when you know that a  
thunderstorm is coming, we  
recommend that you:  
6
Preparation  
Instructions to customer  
Installation  
Attached to this telephone is an approval label. This label is evidence that it is a  
“Permitted Attachment” which has been authorised to be connected to your  
telephone service.  
Conditions relating to connection and operation of this Permitted Attachment are  
contained in Telecommunications General By-Law 220 (5).  
You are authorised to install this Permitted Attachment yourself by plugging it into the  
line socket of any regular telephone. You may connect it in place of your existing  
telephone or to any spare telephone socket installed in your premises.  
To disconnect your existing telephone you must first remove its plug from the line  
socket. You can then insert the plug of your Permitted Attachment into the socket and  
use your equipment.  
If the plug of your existing telephone cannot be readily removed, you will have to  
remove the screw securing it. To do this proceed as follows:  
1
2
3
Loosen screw “A” sufficiently to remove the socket cover. (See Fig. 1.)  
Remove screw “B” and withdraw the plug. (See Fig. 2.)  
Replace screw “B”. (See Fig. 3.) Ensure that it screws completely into the socket  
recess. (If the screw is too long, increase the hole depth or replace the screw with  
one 5 mm shorter.)  
4
Replace socket cover and tighten screw “A”. (See Fig. 4.)  
SOCKET PLUG  
SCREW  
“B”  
SCREW “A”  
TELEPHONE CORD  
Connect to the PLUG  
as shown in Fig. 1.  
Fig. 2  
Fig. 1  
(
)
SCREW “A”  
SCREW  
“B”  
SOCKET  
Fig. 4  
Fig. 3  
7
 
Preparation  
If you are satisfied with the operation of your telephone service after plugging in your  
Permitted Attachment, your installation is completed.  
You will be unable to connect this Permitted Attachment if your telephone service  
consists only of a wall phone or an old style telephone which is not connected by  
means of a modern plug and socket. In such cases a new socket will need to be  
installed.  
Should the Permitted Attachment not operate when plugged into a socket, it is either  
faulty or unsuitable for operation with your telephone service. It should be returned to  
the store where purchased or to an Authorised Service Centre.  
Service difficulties  
If at any time a fault occurs on your telephone service carry out the following checks  
before you call for service:  
L Disconnect the Permitted Attachment and try using the service with the normal  
telephone.  
L If the telephone service then operates satisfactorily, the fault is in your Permitted  
Attachment. Leave the Permitted Attachment disconnected and report the fault to  
its supplier or agent to arrange for repair.  
L If when using the telephone the service is still faulty, report the fault to “Service  
Difficulties and Faults” for attention.  
You are required to keep this Permitted Attachment in good working order while it is  
connected to your telephone service. Its construction or internal circuit must not be  
modified in any way without permission.  
Warning:  
This cordless telephone system does not incorporate provision for secrecy of  
conversations. Appropriately tuned radio equipment and other cordless telephone  
systems in close proximity may be used by a third party to monitor and possibly  
interrupt conversations in progress when this system is on radio operation.  
8
Preparation  
A Speaker  
B {j/OK} (Menu/OK)  
C {k} (Phonebook)  
D {C} (Talk)  
E Navigator key ({^}/{V}/{>}/{<})/  
? (Receiver volume: {^}{V})  
F {s} (Speakerphone)  
G {R} (Recall)  
Controls  
Base unit  
A BCDE  
H Receiver  
I Display  
J {R} (Redial/Pause)  
K {ih} (Off/Power)  
L {C/T} (Clear/Mute)  
M Dial keypad  
F G H IJ  
A Speaker  
N {INT} (Intercom)  
O Microphone  
B {4} (Erase)  
C {7} (Repeat)  
D {8} (Skip)  
P Charge contacts  
E {s} (Answer on)/Answer on  
indicator  
Using the navigator key  
Press {^}, {V}, {<}, or {>} to navigate  
through menus and to select items  
shown on the display.  
F Charge contacts  
G {x} (Page)  
H {<}{>} (Volume)  
I {6} (Play)/Message indicator  
J {} (Stop)  
Adjusting the receiver or speaker  
volume (?)  
Press {^} or {V} while on a call.  
Handset  
{^}  
A
{<}  
{>}  
H
I
J
{V}  
B
C
D
E
K
L
F
M
N
O
G
P
9
 
Preparation  
Displays  
Connections  
Connect the telephone line cord until it  
clicks into the base unit and telephone  
line jack (A). Connect the AC adaptor  
cord (B) by pressing the plug firmly (C).  
Display icons  
Icon  
Meaning  
w
Within range of a base  
unit  
Base unit  
L When flashing:  
Handset is searching  
for base unit.  
C
C
(page 37)  
Hook  
L
Handset is accessing  
base unit. (intercom,  
paging, changing base  
unit settings, etc.)  
k
Handset is on an outside  
call.  
A
B
u
Answering system is on.  
(page 25)  
USE ONLY the  
supplied AC adaptor.  
5
Battery level  
(220240 V, 50/60 Hz)  
Call privacy mode is on.  
(page 16)  
L Line is being used by  
another handset for  
calling, registration,  
etc.  
To telephone line  
USE ONLY the supplied  
cord.  
L Answering system is  
being used by another  
handset or the base  
unit.  
Important:  
L If you use a telephone line cord which  
is not supplied, the unit may not work  
properly.  
10  
     
Preparation  
– Noise is heard during  
conversations.  
Charger (KX-TG1857)  
– Caller ID features (page 23) do not  
function properly.  
C
C
Hooks  
B
(220240 V, 50/60 Hz)  
Telephone  
To socket  
line cord  
USE ONLY the supplied  
AC adaptor (smaller).  
Note:  
Noise filter  
(For ADSL users)  
L Never install telephone wiring during a  
lightning storm.  
L The AC adaptor must remain  
connected at all times. (It is normal for  
the adaptor to feel warm during use.)  
L The AC adaptor should be connected  
to a vertically oriented or floor-  
mounted AC outlet. Do not connect  
the AC adaptor to a ceiling-mounted  
AC outlet, as the weight of the adaptor  
may cause it to become disconnected.  
L The unit will not work during a power  
failure. We recommend connecting a  
standard telephone to the same  
telephone line or to the same  
Location  
L For maximum distance and noise-free  
operation, place your base unit:  
– away from electrical appliances  
such as TVs, radios, personal  
computers, or other phones.  
– in a convenient, high, and central  
location.  
Batteryinstallationand  
replacement  
telephone socket using a telephone  
double adaptor.  
L The unit is not designed to be used  
with rotary (pulse dialling) services.  
Important:  
L Use only the supplied rechargeable  
batteries noted on page 4, 5.  
L USE ONLY rechargeable Ni-MH  
batteries AAA (R03) size.  
If you subscribe to an ADSL service  
L Please attach a noise filter (contact  
your ADSL provider) to the telephone  
line between the base unit and the  
telephone line socket in the event of  
the following:  
L Do NOT use Alkaline/Manganese/Ni-  
Cd batteries.  
L Ensure correct polarities (S, T)  
when installing the batteries.  
11  
   
Preparation  
L Wipe the battery ends (S, T) with a  
dry cloth.  
Battery charge  
Place the handset on the base unit or  
charger for about 7 hours before  
initial use.  
When charging, Chargingwill be  
displayed.  
When the batteries are fully charged,  
Charge Completedwill be  
displayed.  
L When installing the batteries, avoid  
touching the battery ends (S, T) or  
the unit contacts.  
L When replacing batteries, we  
recommend using the Panasonic  
rechargeable batteries noted on page  
4, 5.  
1
Press the notch on the handset  
cover firmly and slide it in the  
direction of the arrow.  
*1  
Base unit  
Charger  
2
Insert the batteries negative (T)  
end first. Close the handset cover.  
Rechargeable Ni-MH ONLY  
*1 KX-TG1857  
Note:  
L It is normal for the handset to feel  
warm during charging.  
L If you want to use the unit  
immediately, charge the batteries for  
at least 15 minutes.  
L Clean the charge contacts of the  
handset, base unit, and charger with a  
soft, dry cloth once a month. Clean  
more often if the unit is subject to the  
exposure of grease, dust, or high  
humidity.  
Note:  
L When replacing batteries, remove the  
old batteries.  
12  
   
Preparation  
Battery level  
Turning the power  
on/off  
Battery icon  
5
Battery level  
High  
6
Medium  
Power on  
7
Low  
Press {ih} for about 1 second.  
L When flashing:  
Needs to be  
charged.  
Power off  
Press {ih} for about 2 seconds.  
Panasonic Ni-MH battery  
performance (supplied batteries)  
Operation  
Operating  
time  
Setting up the unit  
before use  
In continuous use  
Approx. 17  
hours max.  
Display language  
In continuous  
standby mode  
Approx. 180  
hours max.  
1
2
{ih} i {j/OK}  
Note:  
Press {^} or {V} to select  
Handset Setup. i {>}  
L It is normal for batteries not to reach  
full capacity at the initial charge.  
Maximum battery performance is  
reached after a few complete cycles of  
charge/discharge (use).  
3
4
5
Press {^} or {V} to select  
Display Setup. i {>}  
Press {^} or {V} to select  
Select Language. i {>}  
L Actual battery performance depends  
on a combination of how often the  
handset is in use and how often it is  
not in use (standby).  
Press {^} or {V} to select the  
desired language. i {>} i  
{ih}  
L Even after the handset is fully  
charged, the handset can be left on  
the base unit or charger without any ill  
effect on the batteries.  
Note:  
L If you select a language you cannot  
read: {ih} i {j/OK} i {^} 3  
times i {>} i {V} 2 times i  
{>} 2 times i {^}/{V}: Select the  
desired language. i {>} i  
{ih}  
L The battery level may not be  
displayed correctly after you replace  
the batteries. In this case, place the  
handset on the base unit or charger  
and let it charge for at least 7 hours.  
13  
           
Preparation  
Date and time  
1
2
{j/OK}  
Press {^} or {V} to select  
Handset Setup. i {>}  
3
4
5
Press {^} or {V} to select  
Time Settings. i {>}  
Press {^} or {V} to select  
Set Date & Time. i {>}  
Enter the current date, month, and  
year.  
Example: 17 May, 2007  
{1}{7} {0}{5} {0}{7}  
6
7
Enter the current hour and minute.  
Example: 3:30 PM  
{0}{3} {3}{0} i Press {*} until  
03:30 PMis displayed.  
{j/OK} i {ih}  
Note:  
L To correct a digit, press {<} or {>} to  
move the cursor, then make the  
correction.  
L The date and time may be incorrect  
after a power failure. In this case, set  
the date and time again.  
14  
   
Making/Answering Calls  
4
{^}/{V}: Yesi {>} i {ih}  
Making calls  
Pause (for PBX/long distance  
service users)  
A pause is sometimes required when  
making calls using a PBX or long  
distance service.  
Example: If you have to dial {0} before  
dialling outside numbers manually, you  
will probably need to pause after dialling  
{0} until you hear a dial tone.  
1
Lift the handset and dial the phone  
number.  
L To correct a digit, press {C/T}.  
2
3
{C}  
When finished talking, press {ih}  
or place the handset on the base  
unit or charger.  
Speakerphone  
1
2
{0} i {R}  
Dial the phone number. i {C}  
1
During a conversation, press {s} to  
turn on the speakerphone.  
Note:  
L Speak alternately with the caller.  
L A 3 second pause is inserted each  
time {R} is pressed. Repeat as  
needed to create longer pauses.  
2
When finished talking, press  
{ih}.  
Note:  
L For best performance, use the  
speakerphone in a quiet environment.  
L To switch back to the receiver, press  
{C}.  
Answering calls  
1
Lift the handset and press {C} or  
{s} when the unit rings.  
Adjusting the receiver or speaker  
volume  
L You can also answer the call by  
pressing any dial key from {0} to  
{9}, {*}, or {#}. (Any key  
answer feature)  
Press {^} or {V} while on a call.  
Making a call using the redial  
list  
The last 10 phone numbers dialled are  
stored in the redial list (each 24 digits  
max.).  
2
When finished talking, press {ih}  
or place the handset on the base  
unit or charger.  
Auto talk feature  
You can answer calls simply by lifting the  
handset off the base unit or charger. You  
do not need to press {C}. To turn this  
feature on, see page 19.  
1
2
3
{R}  
{^}/{V}: Select the desired number.  
{C}  
Adjusting the handset ringer volume  
when receiving a call  
Erasing numbers in the redial list  
1
2
{R}  
Press {^} or {V}.  
{^}/{V}: Select the desired number.  
i {>}  
3
{^}/{V}: Erasei {>}  
15  
                     
Making/Answering Calls  
and availability of this service in your  
area. Press {R} to answer the 2nd call.  
L To switch between calls, press {R}.  
Handset locator  
Using this feature, you can locate the  
handset if it has been misplaced.  
1
2
Press {x} on the base unit.  
Key lock  
To stop paging, press {x} on the  
base unit or press {ih} on the  
handset.  
The handset can be locked so that no  
calls or settings can be made. Incoming  
calls can be answered, but all other  
functions are disabled while key lock is  
on.  
To turn key lock on, press {j/OK} for  
about 3 seconds.  
Useful features during  
a call  
L Key Lockis displayed.  
L To turn key lock off, press {j/OK}  
again for about 3 seconds.  
Mute  
Note:  
While mute is turned on, you will be able  
to hear the other party, but the other  
party will not be able to hear you.  
To mute your voice, press {C/T}.  
L To return to the conversation, press  
{C/T} again.  
L Calls to emergency numbers cannot  
be made until key lock is turned off.  
Call share  
A 2nd handset can join an existing  
outside call.  
To join the conversation, press {C} or  
{s} when the other handset is on an  
outside call.  
R button (to use the recall  
function)  
Pressing {R} allows you to use special  
features of your host PBX such as  
transferring an extension call, or  
Call privacy  
Call privacy allows you to prevent other  
users from joining your conversations  
with outside callers. To allow other users  
to join your conversations, leave this  
feature off. The default setting is Off.  
accessing optional telephone services.  
Note:  
L To change the recall time, see page  
21.  
1
Press {j/OK} during an outside  
call.  
For Call Waiting service users  
To use Call Waiting, you must subscribe  
to the Call Waiting service of your  
service provider/telephone company.  
This feature allows you to receive calls  
while you are already talking on the  
phone. If you receive a call while on the  
phone, you will hear a Call Waiting tone.  
Please contact your service  
2
{^}/{V}: Onor Offi {>}  
L When this feature is turned on,  
[P]is displayed.  
Note:  
L This feature will turn off after you hang  
up the call.  
provider/telephone company for details  
16  
                     
Phonebook  
L If there is no entry corresponding  
to the letter you selected, the next  
entry will be displayed.  
Handset phonebook  
L To change the character entry  
mode:  
The handset phonebook allows you to  
make calls without having to dial  
manually. You can add 50 names and  
phone numbers.  
{R} i {^}/{V}: Select the  
character entry mode. i {>}  
3
4
{^}/{V}: Scroll through the  
phonebook if necessary.  
Adding entries  
{C}  
1
2
3
{k} i {j/OK}  
{^}/{V}: New Entryi {>}  
Editing entries  
Enter the party’s name (16  
characters max.; page 34). i  
{j/OK}  
1
Find the desired entry (page 17).  
i {j/OK}  
2
3
{^}/{V}: Editi {>}  
4
5
Enter the party’s phone number (24  
digits max.). i {j/OK}  
Edit the name if necessary (16  
characters max.; page 34). i  
{j/OK}  
{^}/{V}: Savei {>} i  
{ih}  
4
5
Edit the phone number if necessary  
(24 digits max.). i {j/OK}  
Note:  
L Step 1 variation:  
{j/OK} i {^}/{V}: Select  
Ph.Book Setup. i {>}  
{^}/{V}: Savei {>} i  
{ih}  
Finding and calling a handset  
phonebook entry  
Erasing an entry  
Scrolling through all entries  
1
Find the desired entry (page 17).  
i {j/OK}  
1
2
3
{k}  
2
3
{^}/{V}: Erasei {>}  
{^}/{V}: Select the desired entry.  
{^}/{V}: Yesi {>} i {ih}  
{C}  
Erasing all entries  
Searching by first character (index  
search)  
1
2
3
4
{k} i {j/OK}  
{^}/{V}: Erase Alli {>}  
{^}/{V}: Yesi {>}  
1
2
{k}  
Press the dial key ({0} to {9}) which  
contains the character you are  
searching for (page 34).  
{^}/{V}: Yesi {>} i {ih}  
L Press the same dial key  
repeatedly to display the first  
entry corresponding to each letter  
located on that dial key.  
17  
               
Phonebook  
Chain dial  
This feature allows you to dial phone  
numbers in the handset phonebook  
while you are on a call. This feature can  
be used, for example, to dial a calling  
card access number or bank account  
PIN that you have stored in the handset  
phonebook, without having to dial  
manually.  
1
2
3
While on a call, press {k}.  
{^}/{V}: Select the desired entry.  
Press {>} to dial the number.  
18  
 
Handset Settings  
Handset settings  
To customise the handset:  
1
2
3
4
5
{j/OK}  
Press {^} or {V} to select Handset Setup. i {>}  
Press {^} or {V} to select the desired item in the handset settings menu. i {>}  
Press {^} or {V} to select the desired item in the sub-menu. i {>}  
Press {^} or {V} to select the desired setting then press {>}.  
L This step may vary depending on the feature being programmed.  
L To exit the operation, press {ih}.  
Note:  
L The current item or setting is indicated by > on the display.  
Menu  
Sub-menu  
Details (default setting)  
Time Settings  
Set Date & Time page 14  
Alarm  
page 20  
*1  
Ringer Setup  
Display Setup  
Ringer Volume  
Ext. Ringtone  
For handset (Maximum)  
For outside calls  
(Ringtone 1)  
*2, *3  
Select  
(English): page 13  
Language  
Contrast  
(Level 3)  
Registration  
Other Options  
Register H.set page 31  
Keytones  
(On)  
Auto Talk  
(Off): page 15  
*1 When the ringer volume is turned off, Ring Offis displayed and the  
handset does not ring for outside calls.  
However even when the ringer volume is turned off, the handset rings:  
– at the minimum level for alarm  
– at the minimum level for intercom calls  
– at the maximum level for paging  
*2 If you select one of the melody ringtones, the ringtone will continue to sound for  
several seconds if the caller hangs up before you answer. You may hear a dial  
tone or no one on the line when you answer a call.  
*3 The preset melodies in this product are used with permission of © 2006  
Copyrights Vision Inc.  
19  
             
Handset Settings  
Special instructions  
for time settings  
Alarm  
An alarm will sound for 3 minutes at the  
set time once or daily. Set the date and  
time beforehand (page 14).  
1
2
{j/OK}  
{^}/{V}: Handset Setupi  
{>}  
3
{^}/{V}: Time Settingsi  
{>}  
4
5
{^}/{V}: Alarmi {>} 2 times  
{^}/{V}: Select an alarm mode. i  
{>}  
Off”  
Turns alarm off. Press {>} again,  
then press {ih} to finish.  
Once”  
The alarm sounds once at the set  
time. Enter the desired date and  
month.  
Daily”  
An alarm sounds daily at the set time.  
6
7
8
Enter the desired hour and minute.  
i {j/OK}  
{^}/{V}: Select the desired ringtone.  
i {>}  
{^}/{V}: Savei {>} i  
{ih}  
Note:  
L To stop the alarm, press any dial key.  
L When in talk or intercom mode, the  
alarm will not sound until the call has  
ended.  
L If you select Once, the setting will  
change to Offafter the alarm  
sounds.  
20  
     
Base Unit Settings  
Base unit settings  
To customise the base unit using the handset:  
1
2
3
{j/OK}  
Press {^} or {V} to select Base Unit Setup. i {>}  
Press {^} or {V} to select the desired item in the base unit settings menu. i  
{>}  
4
5
Press {^} or {V} to select the desired item in the sub-menu. i {>}  
Press {^} or {V} to select the desired setting then press {>}.  
L This step may vary depending on the feature being programmed.  
L To exit the operation, press {ih}.  
Note:  
L The current item or setting is indicated by > on the display.  
Menu  
Sub-menu  
Details (default setting)  
For base unit (Medium)  
Recall time (100 msec.)  
page 22  
Ringer Volume  
Call Options  
*1  
Recall/Flash  
Area Code  
Base Unit PIN  
*2  
Other Options  
Change base unit PIN (0000).  
– Enter the current 4-digit base unit  
*3  
PIN.  
– Enter the new 4-digit base unit  
PIN. i {>} i {ih}  
Repeater Mode  
(Off): page 32  
*1 Change the recall time, if necessary, depending on the requirements of your  
service provider/telephone company or PBX.  
The recall time depends on your telephone exchange or host PBX. Consult your  
PBX supplier if necessary.  
You can access your service provider/telephone company “Call Waiting” service  
by having the recall time set at 100 ms, and then follow your service  
provider/telephone company “Call Waiting” instructions to operate this service.  
*2 If you change the PIN, please make note of your new PIN. The unit will not reveal  
the PIN to you.  
*3 If you forget your PIN, consult your nearest Panasonic service centre.  
21  
           
Base Unit Settings  
Special instructions  
for call options  
Selecting area codes to be  
deleted automatically  
In some situations, phone numbers  
stored automatically in the Caller ID list  
(page 23) will include area codes. If you  
do not want to dial the area codes when  
making calls from the Caller ID list, you  
can store the area codes which you want  
the unit to delete automatically.  
Example: You have stored the area  
code 123. If you make a call from the  
Caller ID list to the phone number  
123-456-7890, the unit dials  
456-7890.  
1
2
{j/OK}  
{^}/{V}: Base Unit Setupi  
{>}  
3
4
5
{^}/{V}: Call Optionsi {>}  
{^}/{V}: Area Codei {>}  
{^}/{V}: Enter an area code (5 digits  
max.). i {j/OK} i {ih}  
22  
     
Caller ID Service  
caller list to see who called while you  
were out.  
Using Caller ID service  
Call waiting and Caller ID  
compatible  
If you subscribe to Caller ID service,  
your handset displays the 2nd caller’s  
information while talking. After you hear  
a call waiting tone, the caller’s phone  
number will be displayed.  
Important:  
L This unit is Caller ID compatible. To  
use Caller ID features (such as  
displaying caller phone numbers), you  
must subscribe to Caller ID service.  
Consult your service  
provider/telephone company for  
details.  
You can answer the 2nd call, keeping the  
1st call on hold. Follow your service  
provider/telephone company  
Caller ID features  
When an outside call is received, the  
caller’s phone number will be displayed.  
L Phone numbers of the last 50 callers  
will be logged in the caller list.  
L While listening to a message recorded  
by the answering system using the  
handset, you can call back the caller  
without having to dial the phone  
number (page 27).  
instructions using {R}. (Recall function)  
L If the phone number is stored in the  
phonebook with its name, the caller’s  
name will also be displayed.  
L Please contact your service  
provider/telephone company for  
details and availability in your area.  
For Caller ID type II users  
L When caller information is received  
and it matches a phone number  
stored in the unit’s phonebook, the  
stored name will be displayed and  
logged in the caller list.  
When you receive a 2nd call during a  
conversation, you will hear a signal tone  
following the call waiting tone and the  
conversation will be interrupted or  
muted for a short period of time. This  
is not the fault of the product as these  
events are normal.  
L If the unit is connected to a PBX  
system, you may not receive the caller  
information.  
L The tones are generated by the  
service provider/telephone company.  
L When the caller dialled from an area  
which does not provide Caller ID  
service, Out of Areawill be  
displayed.  
L When the caller requested not to send  
caller information, either no  
Caller list  
information or Private Caller”  
will be displayed.  
Viewing the caller list and  
calling back  
Missed calls  
1
2
3
{j/OK}  
If a call is not answered, the unit treats  
the call as a missed call. The number of  
missed calls is shown on the display.  
This lets you know if you should view the  
{^}/{V}: Caller Listi {>}  
Press {V} to search from the most  
recent call, or press {^} to search  
from the oldest call.  
23  
           
Caller ID Service  
L If the item has already been  
viewed or answered, “Q” is  
displayed, even if it was viewed or  
answered using another handset.  
3
4
5
{^}/{V}: Select the desired entry.  
i {j/OK}  
{^}/{V}: Add Phonebooki  
{>}  
4
{C}  
Continue from step 3, “Adding  
entries”, page 17.  
Note:  
L If you do not want to dial the area  
codes when making calls from the  
Caller ID list, you can store the area  
codes which you want the unit to  
delete automatically (page 22).  
Voice mail service  
Voice mail is an automatic answering  
service offered by your service  
Editing a caller’s phone  
number before calling back  
provider/telephone company. If you  
subscribe to this service, your service  
provider/telephone company’s voice  
mail system will answer calls for you  
when you are unavailable to answer the  
phone or when your line is busy.  
Messages are recorded by your service  
provider/telephone company, not your  
telephone. Please consult your service  
provider/telephone company for details  
of this service.  
1
2
3
{j/OK}  
{^}/{V}: Caller Listi {>}  
{^}/{V}: Select the desired entry.  
i {j/OK}  
4
5
{^}/{V}: Edit and Calli  
{>}  
Edit the number.  
L Press dial key ({0} to {9}) to add,  
{C/T} to delete.  
Note:  
L To use the voice mail service provided  
by your service provider/telephone  
company rather than the unit’s  
answering system, turn off the  
answering system (page 25). For  
details, see page 29.  
6
{C}  
Erasing caller information  
1
2
3
{j/OK}  
{^}/{V}: Caller Listi {>}  
{^}/{V}: Select the desired entry.  
i {j/OK}  
4
5
{^}/{V}: Eraseor Erase All”  
i {>}  
{^}/{V}: Yesi {>} i {ih}  
Storing caller information into  
the handset phonebook  
1
2
{j/OK}  
{^}/{V}: Caller Listi {>}  
24  
   
Answering System Features  
2
3
{^}/{V}: Answer Systemi  
{>}  
Answering system  
The answering system can answer and  
record calls for you when you are  
unavailable to answer the phone.  
{^}/{V}: Answer Onor  
Answer Offi {>} i {ih}  
Note:  
L When the answering system is turned  
on, u is displayed.  
Important:  
L Only 1 person can access the  
answering system (listen to  
messages, record a greeting  
message, etc.) at a time.  
Greeting message  
When the unit answers a call, callers are  
greeted by a greeting message.  
L When callers leave messages, the  
unit records the date and time of each  
message. Make sure the date and  
time have been set (page 14).  
Recording a greeting  
message  
You can record your own greeting  
message (2 minutes and 30 seconds  
max.).  
Memory capacity  
The total recording capacity (including  
your greeting message and caller  
messages) is about 20 minutes. A  
maximum of 64 messages can be  
recorded.  
1
2
{j/OK}  
{^}/{V}: Answer Systemi  
{>}  
Note:  
L If message memory becomes full:  
Answer Sys. Fullis shown  
on the handset display  
3
{^}/{V}: Record Greetingi  
{>}  
L Hold the handset about 20 cm  
away and speak clearly into the  
microphone.  
{6} on the base unit flashes rapidly  
4
5
Press {j/OK} to stop recording.  
Turning the answering  
system on/off  
{ih}  
Using a pre-recorded greeting  
message  
Using the base unit  
If you erase or do not record your own  
greeting message, the unit plays a pre-  
recorded greeting message for callers  
and asks them to leave messages. If the  
message recording time (page 30) is set  
to Greeting Only, caller messages  
will not be recorded and the unit will play  
a different pre-recorded greeting  
Press {s} to turn on/off the answering  
system.  
L When the answering system is turned  
on, the answer on indicator lights up.  
Using the handset  
1
{j/OK}  
message asking callers to call again.  
25  
                 
Answering System Features  
L If there are no new messages, the  
base unit plays back all messages.  
Playing back the greeting  
message  
Using the handset  
1
2
{j/OK}  
1
2
{j/OK}  
{^}/{V}: Answer Systemi  
{>}  
{^}/{V}: Answer Systemi  
{>}  
3
4
{^}/{V}: Play Greetingi  
{>}  
3
{^}/{V}: Play New Msg.or  
Play All Msg.i {>}  
{ih}  
Operations during playback  
Erasing the greeting message  
To adjust the speaker volume:  
– for the base unit, press {>} or {<}  
– for the handset, press {^} or {V}  
If you erase your own greeting message,  
the unit will play a pre-recorded greeting  
message for callers.  
To repeat a message:  
1
2
{j/OK}  
– for the base unit, press {7}  
– for the handset, press {<}  
{^}/{V}: Answer Systemi  
{>}  
If pressed within the first 5 seconds of  
a message, the previous message will  
be played.  
3
4
5
{^}/{V}: Erase Messagei  
{>}  
{^}/{V}: Erase Greetingi  
{>}  
To skip a message:  
– for the base unit, press {8}  
– for the handset, press {>}  
{^}/{V}: Yesi {>} i {ih}  
To stop a message:  
– for the base unit, press {}  
– for the handset, press {9}  
Listening to messages  
To erase a message:  
– for the base unit, press {4}  
– for the handset, press {*}{4}  
Listening to new/all  
messages  
When you have new messages, {6} on  
the base unit flashes.  
Erasing all messages  
Note:  
Using the base unit  
L When {6} on the base unit flashes  
rapidly, the message memory is full  
(“Memory capacity”, page 25).  
Press {4} 2 times.  
Using the handset  
Using the base unit  
Press {6}.  
L If new messages have been recorded,  
the base unit plays back new  
messages.  
1
2
{j/OK}  
{^}/{V}: Answer Systemi  
{>}  
3
{^}/{V}: Erase Messagei  
{>}  
26  
     
Answering System Features  
4
5
{^}/{V}: Erase Alli {>}  
Key  
Operation  
{^}/{V}: Yesi {>} i {ih}  
{7}{6}  
Record greeting  
message  
Calling back (Caller ID  
subscribers only)  
{8}  
Turn answering system  
on  
If caller information was received for the  
call, you can call the caller back while  
listening to a message.  
{9}  
Stop (recording,  
playback)  
{0}  
Turn answering system  
off  
1
2
Press {j/OK} during playback.  
{^}/{V}: Call Backi {>}  
{*}{4}  
Erase currently playing  
message  
Editing the number before calling  
back  
{*}{5}  
Erase all messages  
{*}{6}  
Erase greeting message  
1
2
Press {j/OK} during playback.  
*1 If pressed within the first 5  
seconds of a message, the  
previous message will be played.  
{^}/{V}: Edit and Calli  
{>}  
3
Edit the number. i {C}  
Remote operation  
Direct command  
operation using the  
handset  
You can operate the answering system  
by pressing dial keys, rather than  
navigating through the menus.  
To use the following commands:  
{j/OK} i  
Using a touch-tone phone, you can call  
your phone number from outside and  
access the unit to listen to messages or  
change answering system settings. The  
unit’s voice guidance will prompt you to  
press certain dial keys to perform  
different operations.  
Important:  
L In order to operate the answering  
system remotely, you must first turn  
on remote operation by setting a  
remote access code. This code must  
be entered each time you operate the  
answering system remotely.  
{^}/{V}: Answer Systemi {>}  
Key  
Operation  
{1}  
Repeat message (during  
playback)  
*1  
{2}  
Skip message (during  
playback)  
Turning remote operation on  
{3}  
Enter the Settings”  
A 3-digit remote access code must be  
entered when operating the answering  
system remotely. This code prevents  
unauthorised parties from listening to  
your messages remotely.  
menu  
{4}  
{5}  
{6}  
Play new messages  
Play all messages  
Play greeting message  
27  
             
Answering System Features  
1
2
{j/OK}  
Key  
Operation  
{^}/{V}: Answer Systemi  
{>}  
{2}  
Skip message (during  
playback)  
3
4
5
{^}/{V}: Settingsi {>}  
{4}  
{5}  
{6}  
{7}  
Play new messages  
Play all messages  
{^}/{V}: Remote Codei {>}  
To turn on remote operation, enter a  
3-digit remote access code.  
L To turn off remote operation,  
press {*}.  
Play greeting message  
Record greeting  
message  
{9}  
Stop (recording,  
playback)  
6
{j/OK} i {ih}  
{0}  
Turn answering system  
off  
Using the answering system  
remotely  
{*}{4}  
Erase currently playing  
message  
1
Dial your phone number from a  
touch-tone phone.  
{*}{5}  
Erase all messages  
2
After the greeting message starts,  
enter your remote access code.  
L The unit will announce the  
number of new messages.  
L After 3 seconds, voice guidance  
starts.  
{*}{6}  
Erase greeting message  
(during greeting message  
playback)  
{*}{#}  
End remote operation (or  
hang up)  
3
Follow the voice guidance prompts  
as necessary.  
*1 If pressed within the first 5  
seconds of a message, the  
previous message will be played.  
Note:  
L You can hang up at any time.  
Turning on the answering  
system remotely  
If the answering system is off, you can  
turn it on remotely.  
Voice guidance  
During remote operation, the unit’s voice  
guidance will prompt you to press {1} to  
perform a specific operation, or press  
{2} to listen to more available  
operations.  
1
2
3
Dial your phone number from a  
touch-tone phone.  
Let the phone ring 15 times.  
Remote commands  
L A long beep will be heard.  
You can press dial keys to access  
certain answering system functions  
without waiting for the voice guidance to  
prompt you.  
Enter your remote access code  
within 10 seconds after the long  
beep.  
L The greeting message is played  
back.  
Key  
Operation  
L You can hang up, or enter your  
remote access code again and  
begin remote operation.  
{1}  
Repeat message (during  
playback)  
*1  
28  
     
Answering System Features  
For Service Provider Voice Mail  
Subscribers  
Answering system  
settings  
To receive Voice Mail and use answering  
system properly, please note the  
following:  
Setting (default setting)  
Page  
L “Voice Mail” is a service provided by  
your service provider/telephone  
company. You will need to first  
subscribe or activate this service  
through your service  
provider/telephone company. Consult  
your service provider/telephone  
company on how to operate this  
service and how you will be notified  
that you have messages on your  
Voice Mail.  
Answering system on/off  
(Answer On)  
25  
Remote access code  
(—)  
27  
29  
30  
30  
Number of rings  
(4 Rings)  
Caller’s recording time  
(3 Minutes)  
Call screening  
(On)  
To use this service you will be required  
to leave your answering machine off  
on your unit.  
Number of rings  
This will allow the Voice Mail to  
receive any messages.  
You can change the number of times the  
phone rings before the unit answers  
calls. You can select 2 to 7 rings, or  
Auto.  
This unit does not have a visual  
indicator to indicate if there are new  
messages in your Voice Mail service.  
Your service provider/telephone  
company may use a “Stutter” dial tone  
to indicate that you have Voice Mail  
left.  
Auto: The unit answers after 2 rings  
when new messages have been  
recorded, and after 5 rings when there  
are no new messages. If you call your  
phone from outside to listen to new  
messages (page 28), you will know that  
there are no new messages when the  
phone rings for the 3rd time. You can  
then hang up without being charged for  
the call.  
L To use the unit’s answering machine  
rather than the Voice Mail service  
provided by your service  
provider/telephone company, please  
consult your service  
provider/telephone company to have it  
removed or deactivated permanently  
or temporarily.  
1
2
{j/OK}  
{^}/{V}: Answer Systemi  
{>}  
Alternatively you can leave this  
service connected and change the  
Number of Ringsto a shorter  
duration on your unit so your unit’s  
answering machine can pick up the  
call prior to the Voice Mail provided by  
your service provider/telephone  
company.  
3
4
{^}/{V}: Settingsi {>}  
{^}/{V}: Number of Ringsi  
{>}  
5
{^}/{V}: Select the desired setting.  
i {>} i {ih}  
29  
         
Answering System Features  
Note:  
L Provider Voice Mail can capture  
messages that can be missed while  
the customer is on the Internet.  
Caller’s recording time  
You can change the maximum message  
recording time allotted to each caller, or  
set the unit to greet callers but not record  
messages.  
1
2
{j/OK}  
{^}/{V}: Answer Systemi  
{>}  
3
4
{^}/{V}: Settingsi {>}  
{^}/{V}: Recording Timei  
{>}  
5
{^}/{V}: Select the desired setting.  
i {>} i {ih}  
Call screening  
While a caller is leaving a message, you  
can screen the call through the handset  
speaker.  
1
2
{j/OK}  
{^}/{V}: Answer Systemi  
{>}  
3
4
{^}/{V}: Settingsi {>}  
{^}/{V}: Call Screeningi  
{>}  
5
{^}/{V}: Onor Offi {>} i  
{ih}  
30  
     
Multi-unit Operation  
5
6
Press and hold {x} on the base unit  
for about 5 seconds, until the  
registration tone sounds.  
Operating additional  
units  
L If all registered handsets start  
ringing, press {x} to stop, then  
repeat this step.  
Additional handsets  
Up to 6 handsets can be registered to  
the base unit.  
L After pressing {x}, the rest of this  
procedure must be completed  
within 90 seconds.  
Important:  
Wait until Enter Base PINis  
displayed. i Enter the base unit  
PIN (default: 0000). i {j/OK}  
L If you forget your PIN, consult  
your nearest Panasonic service  
centre.  
L The additional handset model  
recommended for use with this unit is  
noted on page 4. If other model  
handset is used, certain operations  
(handset settings, base unit settings,  
etc.) may not be available.  
L When the handset has been  
registered successfully, w will  
stop flashing. If the key tone is  
turned on (page 19), a  
L Additional handsets will give you the  
freedom to, for example, have an  
intercom call with another handset  
while a third handset is on an outside  
call.  
confirmation tone will be heard.  
Deregistering a handset  
A handset can cancel its own  
registration (or the registration of  
another handset) that is stored in the  
base unit. This will allow the base unit to  
“forget” the handset.  
Registering a handset  
to the base unit  
The supplied handset and base unit are  
pre-registered. When you purchase an  
additional handset, refer to the additional  
handset’s installation manual for  
registration. If for some reason the  
handset is not registered to the base unit  
(for example, w flashes even when the  
handset is near the base unit), register  
the handset.  
1
2
{j/OK}  
{^}/{V}: Base Unit Setupi  
{>}  
3
4
Enter 335.  
{^}/{V}: Deregistrationi  
{>}  
L The numbers of all handsets  
registered to the base unit are  
displayed.  
1
2
{j/OK}  
{^}/{V}: Handset Setupi  
{>}  
5
Select the handset(s) you want to  
cancel, by pressing the desired  
handset number. i {j/OK}  
L The selected handset number(s)  
will flash.  
3
4
{^}/{V}: Registrationi {>}  
{^}/{V}: Register H.seti  
{>}  
31  
             
Multi-unit Operation  
L To cancel a selected handset  
number, press the number again.  
The number will stop flashing.  
Intercom between  
handsets  
Intercom calls can be made between  
handsets.  
6
7
{^}/{V}: Yesi {>}  
L A long beep will sound as each  
handset number disappears.  
L The handset does not beep when  
cancelling its own registration.  
Example: When handset 1 calls  
handset 2  
{ih}  
1
Handset 1:  
{INT} i Press {2} (desired  
handset number).  
Increasing the range of the  
base unit  
You can increase the signal range of the  
base unit by using a DECT repeater.  
Please use only the Panasonic DECT  
repeater noted on page 4. Consult your  
Panasonic dealer for details.  
2
3
Handset 2:  
{C}  
When finished talking, press  
{ih}.  
Important:  
Transferring calls  
between handsets  
L Before registering the repeater to this  
base unit, you must turn the repeater  
mode on.  
Outside calls can be transferred  
between 2 people.  
L Do not use more than one repeater at  
a time.  
Example: When handset 1 transfers a  
call to handset 2  
Setting the repeater mode  
1
Handset 1:  
1
2
{j/OK}  
During an outside call, press {INT}.  
i Press {2} (desired handset  
number).  
{^}/{V}: Base Unit Setupi  
{>}  
3
4
5
{^}/{V}: Other Optionsi  
{>}  
L The outside call will be put on  
hold.  
{^}/{V}: Repeater Modei  
{>}  
L If there is no answer, press {INT}  
to return to the outside call.  
{^}/{V}: Onor Offi {>} i  
{ih}  
2
3
Handset 2:  
Press {C} to answer the page.  
L Handset 2 can talk with handset  
1.  
Note:  
L After turning repeater mode on or off,  
w will flash on the handset  
momentarily. This is normal. The  
handset can be used once w stops  
flashing.  
Handset 1:  
To complete the call transfer, press  
{ih}.  
32  
           
Multi-unit Operation  
To establish a conference call, press  
{3}.  
Transferring a call without speaking  
to the other handset user  
1
During an outside call, press {INT}.  
i Press the desired handset  
number.  
Copying phonebook  
entries  
L k flashes to indicate the outside  
call is on hold.  
You can copy handset phonebook  
entries to the handset phonebook of  
2
{ih}  
L The outside call rings at the other  
handset.  
Note:  
Copying one entry  
L If the other handset user does not  
answer the call within 1 minute, the  
call will ring at your handset again.  
1
Find the desired handset  
phonebook entry (page 17). i  
{j/OK}  
2
3
{^}/{V}: Copyi {>}  
Enter the handset number you wish  
to send the handset phonebook  
entry to.  
Conference calls  
2 people can have a conference call with  
an outside party. The following 2  
methods are available:  
L When an entry has been copied,  
Completedis displayed.  
L To continue copying another  
entry:  
– Another person presses {C} or {s}  
while one person is talking with an  
outside party (“Call share”, page 16).  
– One person pages another person  
during an outside call as follows.  
{^}/{V}: Yesi {>} i Find  
the desired handset phonebook  
entry. i {>}  
4
{ih}  
Example: When handset 1 pages a call  
to handset 2  
Copying all entries  
1
Handset 1:  
1
2
3
{k} i {j/OK}  
During an outside call, press {INT}.  
i Press {2} (desired handset  
number).  
{^}/{V}: Copy Alli {>}  
Enter the handset number you wish  
to send the handset phonebook  
entry to.  
L The outside call will be put on  
hold.  
L If there is no answer, press {INT}  
to return to the outside call.  
L When all entries have been  
copied, Completedis  
displayed.  
2
3
Handset 2:  
Press {C} to answer the page.  
L Handset 2 can talk with handset  
1.  
4
{ih}  
Handset 1:  
33  
       
Useful Information  
Character entry  
The dial keys are used to enter characters and numbers. Each dial key has multiple  
characters assigned to it. The available character entry modes are Alphabet (ABC),  
Numeric (0-9), Greek (F), Extended 1 (G), Extended 2 (H), and Cyrillic  
(I). When in these entry modes except Numeric, you can select which character  
is entered by pressing a dial key repeatedly.  
– Press {<} or {>} to move the cursor.  
– Press dial keys to enter characters and numbers.  
– Press {C/T} to erase the character or number highlighted by the cursor. Press  
and hold {C/T} to erase all characters or numbers.  
– Press {*} to switch between uppercase and lowercase.  
To enter another character located on the same dial key, press {>} to move the  
cursor to the next space, then press the appropriate dial key.  
Character entry modes  
Several character entry modes can be used when entering text. The characters that  
can be entered depend on the entry mode.  
Characters available in each character entry mode  
When the unit displays the character entry screen:  
{k} i {^}/{V}: Select a character entry mode. i {>}  
Alphabet character table (ABC)  
Numeric entry table (0-9)  
Greek character table (M)  
34  
     
Useful Information  
Extended 1 character table (N)  
L The following are used for both uppercase and lowercase:  
Extended 2 character table (O)  
L The following are used for both uppercase and lowercase:  
Cyrillic character table (P)  
35  
Useful Information  
Error messages  
Error message  
Cause & solution  
Answer Sys. Full L Erase unnecessary messages (page 26).  
Error  
L Recording was too short. Try again.  
Failed  
L Phonebook copy failed. Confirm the other handset  
(the receiver) is in standby mode and try again.  
Incomplete  
L The receiver’s phonebook memory is full. Erase the  
unnecessary phonebook entries from the other  
handset (the receiver) and try again.  
Memory Full  
L The handset’s phonebook memory is full. Erase  
unnecessary entries (page 17).  
L Message memory becomes full. Erase  
unnecessary messages (page 26).  
No link to base.  
Move closer to  
base, try again.  
L The handset has lost communication with the base  
unit. Move closer to the base unit and try again.  
L Unplug the base unit’s AC adaptor to reset the unit.  
Reconnect the adaptor and try again.  
L The handset’s registration may have been  
cancelled. Re-register the handset (page 31).  
You must first  
subscribe to  
Caller ID.  
L You must subscribe to Caller ID service. Once you  
receive caller information after subscribing to Caller  
ID service, this message will not be displayed.  
36  
 
Useful Information  
Troubleshooting  
If you still have difficulties after following the instructions in this section, disconnect  
the base unit AC adaptor and turn off the handset, then reconnect the base unit AC  
adaptor and turn on the handset.  
Telephone  
Problem  
Cause & solution  
w is flashing.  
L The handset is not registered to the base unit.  
Register it (page 31).  
L The handset is too far from the base unit. Move  
closer.  
L The base unit AC adaptor is not connected. Check  
the connections.  
L You are using the handset or base unit in an area  
with high electrical interference. Place the handset  
and base unit away from interference sources,  
such as antennas and mobile phones.  
The handset display is L The handset is not turned on. Turn the power on  
blank.  
(page 13).  
The handset will not  
turn on.  
L Make sure that the batteries are installed correctly  
(page 11).  
L Fully charge the batteries (page 12).  
L Clean the charge contacts and charge again  
(page 12).  
I have changed the  
display language to a  
language I cannot  
read.  
L Change the display language (page 13).  
37  
   
Useful Information  
Problem  
Cause & solution  
I cannot make or  
receive calls.  
L The base unit AC adaptor or telephone line cord is  
not connected. Check the connections.  
L If you are using a splitter to connect the unit,  
remove the splitter and connect the unit to the wall  
socket directly. If the unit operates properly, check  
the splitter.  
L Disconnect the base unit from the telephone line  
and connect the line to a known working telephone.  
If the working telephone operates properly, contact  
our service personnel to have the unit repaired. If  
the working telephone does not operate properly,  
contact your service provider/telephone company.  
L The key lock feature is turned on. Turn it off  
(page 16).  
L The unit is not designed to be used with rotary  
(pulse dialling) services.  
The unit does not ring. L The ringer volume is turned off. Adjust the ringer  
volume (page 19, 21).  
The batteries should  
be charging but the  
battery icon does not  
change.  
L Clean the charge contacts and charge again  
(page 12).  
A busy tone is heard  
when {C} is pressed.  
L The handset is too far from the base unit. Move  
closer and try again.  
L Another handset is in use or the answering system  
is being used. Wait and try again later.  
Static is heard, sound L Place the handset and the base unit away from  
cuts in and out.  
other electrical appliances.  
Interference from  
other electrical units.  
L Move closer to the base unit.  
L Your unit is connected to a telephone line with  
ADSL service (page 40).  
Noise is heard during  
a call.  
L You are using the handset or base unit in an area  
with high electrical interference. Place the handset  
and base unit away from interference sources,  
such as antennas and mobile phones.  
The handset/base unit L Disconnect the base unit AC adaptor and turn off  
stops working while  
the handset. Connect the base unit AC adaptor,  
being used.  
turn on the handset and try again.  
The handset beeps  
intermittently and/or  
7 flashes.  
L Fully charge the batteries (page 12).  
38  
Useful Information  
Problem  
Cause & solution  
I fully charged the  
batteries, but 7 still  
flashes.  
L Clean the charge contacts and charge again  
(page 12).  
L It is time to replace the batteries (page 11).  
I fully charged the  
batteries, but the  
operating time seems  
to be short.  
L Wipe the battery ends (S, T) and the unit contacts  
with a dry cloth. Change the batteries for 7 hours  
before reuse.  
Caller information is  
not displayed.  
L You need to subscribe to Caller ID service. Consult  
your service provider/telephone company for  
details.  
L Caller has withheld information.  
L Your unit is connected to a telephone line with  
ADSL service (page 40).  
I cannot register a  
handset to the base  
unit.  
L The maximum number of handsets (6) are already  
registered to the base unit. Cancel unused handset  
registrations from the base unit (page 31).  
L You entered the wrong PIN. If you forget your PIN,  
consult your nearest Panasonic service centre.  
L Place the handset and the base unit away from  
other electrical appliances.  
I do not know how to  
erase the missed call  
number (for example,  
3 Calls) from the  
display.  
L There are unviewed missed calls remaining. View  
them using the following method.  
1
2
3
{j/OK}  
{^}/{V}: Caller Listi {>}  
Press {V} to search from the most recent call, or  
press {^} to search from the oldest call.  
Answering system  
Problem  
Cause & solution  
The unit does not  
record new messages.  
L The answering system is turned off. Turn it on  
(page 25).  
L The recording time is set to Greeting Only.  
Select 1 Minuteor 3 Minutes(page 30).  
L If you subscribe to the voice mail service,  
messages are recorded by your service  
provider/telephone company not your telephone.  
Change the unit’s Number of Ringssetting or  
consult your service provider/telephone company  
(page 29).  
39  
Useful Information  
Problem  
Cause & solution  
I cannot operate the  
answering system with  
the handset.  
L The base unit or another handset is being used.  
Wait for the other user to finish.  
L A caller is leaving a message. Wait for the caller to  
finish.  
L The handset is too far from the base unit. Move  
closer.  
When I try to operate  
the answering system  
with the base unit, the  
answer on indicator on  
the base unit flashes  
for a few seconds and  
I cannot operate the  
answering system.  
L Another handset is being used. Wait for the other  
user to finish.  
L A caller is leaving a message. Wait for the caller to  
finish.  
I cannot operate the  
answering system  
remotely.  
L You are entering the wrong remote access code. If  
you forget the remote access code, store a new  
remote access code (page 27).  
L Press each key firmly.  
L The answering system is turned off. Turn it on  
(page 28).  
L You are using a rotary/pulse telephone. Try again  
using a touch-tone phone.  
While recording a  
greeting message or  
listening to messages,  
the unit rings and  
recording stops.  
L A call is being received. Answer the call and try  
again later.  
For ADSL users  
We recommend connecting a filter (contact your ADSL service provider) to the  
telephone line between the base unit and the telephone line socket.  
40  
 
Useful Information  
Handset: Approx. 130 g  
*1  
Charger : Approx. 60 g  
Specifications  
*1 KX-TG1857  
Standard:  
GAP (Generic Access Profile)  
Note:  
L Specifications are subject to change.  
L The illustrations used in these  
operating instructions may differ  
slightly from the actual product.  
Number of channels:  
120 Duplex Channels  
Frequency range:  
1.88 GHz to 1.90 GHz  
Duplex procedure:  
TDMA (Time Division Multiple  
Access)  
Channel spacing:  
1,728 kHz  
Bit rate:  
1,152 kbit/s  
Modulation:  
GFSK (Gaussian Frequency Shift  
Keying)  
RF transmission power:  
Approx. 250 mW  
Voice coding:  
ADPCM 32 kbit/s  
Power source:  
220–240 V, 50/60 Hz  
Power consumption  
Base unit:  
Standby: Approx. 1.9 W  
Maximum: Approx. 5.3 W  
*1  
Charger  
:
Standby: Approx. 0.9 W  
Maximum: Approx. 4.5 W  
Operating conditions:  
5 °C–40 °C, 20 %–80 % relative air  
humidity (dry)  
Dimensions:  
Base unit: Approx. 54 mm × 122 mm  
× 137 mm  
Handset: Approx. 155 mm × 48 mm ×  
32 mm  
*1  
Charger : Approx. 53 mm × 81 mm ×  
91 mm  
Mass (weight):  
Base unit: Approx. 210 g  
41  
   
Index  
R
Recall: 16, 21  
Index  
Repeater: 32  
A
Additional handsets: 31  
Alarm: 20  
Answering calls: 15  
Answering system: 25  
Listening to messages: 26  
Remote operation: 27  
Settings: 29  
Ringtone: 19  
S
T
V
Transfer calls: 32  
Turning on/off: 25  
Auto talk: 15, 19  
B
C
Base unit  
Settings: 21  
Battery: 11, 13  
Ringer (Base unit): 21  
Caller ID service: 23  
Call privacy: 16  
Call share: 16  
Call waiting: 16  
Chain dial: 18  
Character entry: 34  
Conference calls: 33  
D
H
Date and time: 14  
Display  
Contrast: 19  
Icons: 10  
Language: 13  
Handset  
Deregistration: 31  
Locator: 16  
Registration: 31  
Settings: 19  
I
Intercom: 32  
K
Key lock: 16  
Keytones: 19  
M
P
Making calls: 15  
Missed calls: 23  
Mute: 16  
Pause: 15  
Phonebook  
Handset phonebook: 17  
Phonebook copy: 33  
PIN: 21  
Power on/off: 13  
42  
   
Notes  
43  
Customer Support Centre Tel. No.:  
N52  
Sales Department:  
Panasonic Australia Pty. Limited  
Austlink Corporate Park  
1 Garigal Road  
Belrose  
NSW 2085  
AUSTRALIA  
Panasonic Communications Co., Ltd.  
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan  
Copyright:  
This material is copyrighted by Panasonic Communications Co., Ltd., and may be  
reproduced for internal use only. All other reproduction, in whole or in part, is  
prohibited without the written consent of Panasonic Communications Co., Ltd.  
© 2007 Panasonic Communications Co., Ltd. All Rights Reserved.  
PQQX16085ZA CC0607DV0  

Mitsubishi Electronics Msz A30yv User Manual
Mitsubishi Electronics Prh 5 User Manual
Panasonic Hq 2051rh User Manual
Samsung Avmdh072ca0 User Manual
Samsung St550 User Manual
Sanyo Sha Kc64ug User Manual
Soleus Air Ph5 13r 35d User Manual
Subaru Robin Power Products Pkx301t User Manual
Whirlpool Acd052pk0 User Manual
Xerox Synergix 8825 User Manual